Brake master cylinder: 4CV (2nd Model) / Dauphine / Floride / Alpine A108
Clutch transmitter: Matra Djet
In stock
Braking Alpine A108 / Interlagos
Our braking spare parts for the Renault Alpine A108 / Interlagos.
Discover here a wide choice of parts to restore and ensure the proper functioning of the braking system of your Renault Alpine A108 / Interlagos.
Whether you are looking for wheel cylinders, hoses, master cylinders, brake discs, original brake calipers, lockheed, reservoir, connector, stop switch, repair kit, copper braking circuit...at AVP, Arnaud Ventoux Pièces, you will find everything you need to bring your old one back to life with quality components.
Length taken from the axis of the fixing eye to the end of the rod: min adjustment 105mm / max 115mm
In stock
Mounts with the stop switch reference 4423
In stock
In stock
Thread (master cylinder side): M16x150
Nozzle (rubber hose connection side): Ø 10mm
In stock
In stock
Master Cylinder Side (Male Thread): M16x150
Copper Pipe Fitting Side (Female Thread): Ø 1/2"-20 UNF (Ø 12.70mm)
In stock
In stock
In stock
Suitable for:
Dauphine (All models): Drum brake
Florida / Alpine A108: Drum brake
In stock
Suitable for:
Dauphine (All models): Drum brake
Florida / Alpine A108: Drum brake
In stock
The hose outlet is oblique: Ø 3/8" - 24UNF(Ø 9.52mm)
Suitable for:
4CV: Front Left Brake (From early 1956 to late 1956)
Dauphine / Floride : Front Right Brake
R8 (Drum Brake): Rear Right Brake
In stock
Angled hose outlet: Ø 3/8" - 24UNF(Ø 9.52mm)
Suitable for:
4CV: Right Front Brake (Early 1956 to Late)
Dauphine / Floride : Left Front Brake
R8 (drum brake): Left Rear Brake
In stock
Slanted hose outlet: Ø 3/8" - 24UNF (Ø 9.52mm)
In stock
Slanted hose outlet: Ø 3/8" - 24UNF (Ø 9.52mm)
In stock
In stock
In stock
This kit contains an M9 adjustment screw nut and an M8 nut.
Kit sold with a strong Ø 38mm square gasket and a weak Ø 38mm gasket.
The supply of these two seals allows you to install the most suitable seal depending...
In stock
This kit contains an M9 adjustment screw nut and an M8 nut.
To identify a caliper with a square or round seal, refer to the symbol indicated on the caliper casting.
The "square" symbol indicates the presence of a...
In stock
This kit contains an M9 adjustment screw nut and an M8 nut
To identify a caliper with a square or round joint, refer to the symbol indicated on the caliper casting.
A square symbol indicates a square joint, while a...
Out of stock
This kit contains an M9 adjustment screw nut and an M8 nut
To identify a caliper with a square or round seal, refer to the symbol indicated on the caliper casting.
A square symbol indicates a square seal, while a...
In stock
- Sold complete with support, brass cap, insert and rubber teat
- Jar mounted with rubber teat Ø 6mm
In stock
Sold complete with teat (inside Ø 6mm), insert, support and cap.
In stock
In stock
In stock
In stock
Sold in 1ml lengths
In stock
Suitable for:
4CV: Drum brake (From 06/1953 until end of series)
Alpine A106: Drum brake
Dauphine (All models): Disc brake
Caravelle / Floride: Disc brake
R10 / R8 (All models): Disc brake
Alpine A110 and GT4: Disc...
In stock
Suitable for:
4CV: Drum brake (From 06/1953 until end of series)
Alpine A106: Drum brake
Dauphine (All models): Disc brake
Caravelle / Floride: Disc brake
R10 / R8 (All models): Disc brake
Alpine A110 and GT4: Disc...
In stock
Outer diameter: 260mm
Hub passage diameter: 60mm
Center distance of the 3 fixing holes: 71mm
Thickness: 8mm
In stock
It is mandatory to change the calipers in pairs (Right and left caliper)
In stock
It is mandatory to change the calipers in pairs (Right and left caliper)
In stock
It is mandatory to change the calipers in pairs (Right and left caliper)
In stock
It is mandatory to change the calipers in pairs (Right and left caliper)
In stock
For a cable with a cable stop end: Ø 14mm
OE Renault Ref: 8704054 / 0870405400
In stock
In stock
In stock
Out of stock
In stock
In stock
In stock
Delivery in France only
Does not absorb moisture, thus protecting brake systems from rust, which accumulates on wheel cylinders and destroys the brake pads after a few brake applications when the brakes are restarted...
In stock
Ideal for degreasing all your braking elements or other mechanical parts.
In stock
Suitable for taps: M3 to M10
Short tap holder - Length 85 mm
Reversible ratchet: Left-hand, right-hand, and fixed ratchet
Two-jaw steel grip
In stock
UNF thread tap (2B tolerance): Ø 3/8"-24 UNF (Right-hand thread)
Tap length (Overall): 63 mm
Mounting drive: 5.5 mm square
Flat end tap, suitable for: Through and blind holes
Machine tap: Only one tap is needed to...
In stock
Suitable for die outer diameter: Ø 38.1mm
Die height: 12.7mm
Two-arm die holder made of high-quality steel
In stock
ISO standard metric die: M10x125 (Fine thread - Right-hand thread)
Die outer diameter: Ø 38.1 mm
Die height: 13.1 mm
Suitable for the following materials: Soft steel / Hard steel / Cast iron / Stainless steel /...
In stock
ISO standard metric die: M12x125 (Fine thread - Right-hand thread)
Die outer diameter: Ø 38.1 mm
Die height: 12.8 mm
Suitable for the following materials: Soft steel / Hard steel / Cast iron / Stainless steel /...
In stock
Suitable for die outer diameter: Ø 30mm
Die height: 10mm
Two-arm die holder made of high-quality steel
In stock
UNF die, DIN223 standard: Ø 3/8"-24 UNF (Right-hand thread)
Outer diameter of the die: Ø 30 mm
Die height: 11 mm
Suitable for the following materials: Soft steel / Hard steel / Cast iron / Stainless steel / Aluminum...
In stock