Grease nipple with steel ball
Grease nipple (overall) height: 18mm
Grease nipple with a 9 key
In stock
Best sellers
Grease nipple with steel ball
Grease nipple (overall) height: 25mm
Grease nipple with an 11mm key
In stock
In stock
Air bypass screw for carburettor WEBER 40DCOE and 45DCOE
Number 26 On exploded view
Also suitable for the following carburettors: 36 DCNF 36 DCNFA 40 / 45 DCOE 40 IT .
In stock
Suitable for WEBER 40DCOE and 45DCOE carburettor
Sold individually, need 2 pieces for one carburettor
Part number 65 on exploded view
In stock
In some configurations, Weber DCOE carburetors are positioned directly above the exhaust, which can create vapor lock problems due to heat: our AVP48010 plate can solve this problem
Plate can be covered with thermal...
In stock
In stock
This igniter is suitable for:
R5 Alpine (R1223)
Igniter to be used with a coil with a primary resistance of 2.5 to 3.5 ohms
Compatible with coils AVP4708 and AVP4715
Instructions included
In stock
Thickness: 1.7mm (repair side)
Oblong “Lunules” type cylinder head gasket.
In stock
In stock
Master cylinder inner diameter: Ø 19.05mm
Outlet diameters (x4): Ø 10x100 (x3) and Ø 12x100 (x1)
Renault OE part number: 7700590483 / 7700638947 / 7701348924
Suitable for:
R16 TL (R1152): 2nd model
R16 TX / TL...
In stock
In stock
In stock
In stock
In stock
Lock cylinder supplied with key and duplicate (2 keys per cylinder)
Overall length of the cylinder: 28mm
Length from the head to the fixing point: 23mm
Cylinder head diameter: Ø 15.20mm
Cylinder diameter: Ø 12mm...
In stock
Nut Specifications:
Thread Diameter: M8
Knurled Height: 9.5 mm
Sold individually, requires three screws
Renault OE Ref: 0607968000 / 7703033003
In stock
In stock
Piston diameter: Ø 53 mm (Minimum) to Ø 125 mm (Maximum)
Tool height: 75 mm
Supplied with a square tightening wrench
Ideal tool for installing pistons in the cylinder block
Out of stock
In stock
To be installed with a straight grease nipple M6x100 (AVP C107)
Specific screw: M12x150 (Fine Pitch)
OE Renault Ref: 8546170 / 0854617000
In stock
Length under head: 25mm
Overall length: 30mm
Suitable for:
A310.4: From chassis no. 1 to no. 634 (1st model)
In stock
Suitable for: 4L After 09-1974 / 34L Tank
Specifications:
Dipstick length: 170mm
Suction pipe outer diameter: 6mm
Total height: 192mm
Connection via 1 flat plug
Supplied with a quarter-turn fixing ring and gasket
In stock
Sheet Dimensions: Length 50cm x Width 33cm
Sheet Thickness: 3mm
Ideal for making oil pan gaskets, timing case gaskets, and cylinder head cover gaskets. These gaskets must be installed with a light clamping force....
In stock
Allows to clamp the horns on the body of the WEBER 45DCOE carburetor
ATTENTION: essential for REF 48096 horns.
Kit for a carburetor consisting of 4 stop tabs, 4 washers and 4 nuts
Also suitable for WEBER 48DCOE...
In stock
Tools to be used with a wrench or a socket of Size 36
In stock
Out of stock
Delivered without fuses
Dimensions: Lg 60mm x W 47mm x H 27mm - Fixing distance: 45mm
In stock
Out of stock
Thickness : 1mm
Compatible with 1565cm³ to 1647cm³ engines (Type 807 844 and 843):
A110 1600S/SC/SX
A310 1600cc
R12G / R17G
R16.TS/TX
In stock
Connectors : M12X100 (x2) and in M10x100 (x2)
In stock
Out of stock
In stock
Delivery in France only
250ml
Formulated exclusively for painting steel exhausts
Guaranteed temperature resistance of 400°C, resistant to gasoline, strong anti-corrosion properties
In stock
Suitable for:
Juvaquatre R2100 (4hp): Type 662-3 engine
Dauphinois R2101 (5hp): Type 670-2 engine
In stock
Out of stock
Suitable for: Box 365-05 / 365-33 / 365-35
In stock
Use reserved for competition, do not use these pads on public roads.
In stock
Out of stock
In stock
Segment Characteristics:
Segment Diameter: Ø 77.1 mm
Thickness of Upper Segments (Fire-resistant): 1.75 mm
Thickness of Intermediate Segments (Waterproof): 2mm
Low ring thickness (Scraper): 4mm
It is essential to...
In stock
In stock
Segment Characteristics:
Segment Diameter: Ø 77.8mm
Thickness of Upper Segments (Fire-resistant): 1.75mm
Thickness of Intermediate Segments (Waterproof): 2mm
Low ring thickness (Scraper): 4mm
It is essential to...
In stock
Suitable for:
R5 Alpine (R1223)
R5 Alpine Turbo (R122B)
In stock
In stock
In stock
Suitable for vehicles:
4CV / Juvaquatre: Type 662 Engine (From June 1956)
Dauphine / Dauphinoise / Estafette / Floride A106 / A108: Type 670 Engine
R4: Billancourt Type 800-02/05 Engine (From 1962)
Bearing...
In stock
Dimensions:
L: 12.1 mm
b1: 12 mm
h:8.5 mm
d: M6 x 100
B: 8.1 mm
A: 12.1 mm
F1: 1.2 → 1.6 mm
Suitable for the following vehicles:
R8: For underbody sheet metal:08524978
R16: Front Wings
In stock
Sold in 1ml lengths
In stock
In stock
Suitable for WEBER 40DCOE and WEBER 45DCOE carburettors.
Wire thickness 1 mm and wound length 33 mm.
Number 50 on exploded view
Also suitable for the following carburettors: 38 DCOE, 40 DCOE, 42 DCOE, 45 DCOE.
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Number 78 on exploded view
Compatible with other WEBER carburetors, see below
In stock
The entire kit is composed of 3/8"-24UNF and M10x100 fittings
This kit is composed of the following copper pipes:
- From the brake master cylinder to the Right Front Wheel
- From the brake master cylinder to the Left...
In stock
In stock
Out of stock
Segment Characteristics:
Segment Diameter:Ø 88mm
Thickness of Upper Segments (Fire-resistant): 1.5mm
Thickness of Intermediate Segments (Waterproof): 2mm
Low ring thickness (Scraper): 4mm
It is essential to...
In stock
This lighter is suitable for:
- R8G / A110 (1108cc / 1255cc / 1296cc)
Kit to be used with a primary resistance coil between 2.5 and 3.5 ohms
Compatible with AVP4708 and AVP4715 coils
In stock
3 x Fittings: Ø 3/8"-24UNF (Ø 9.52mm)
2 x Mounting Holes
Suitable for:
R4 / 4L: From 1968 to 1976
R5 TL / R5 TS
R16 TS
Out of stock
Out of stock
In stock
Delivery in France only
Anti-corrosion paint for engine block, crankcase, brake drum, and gearbox.
Resistant to 180°C
Capacity: 500ml
Color: Bright Blue RAL 5005
Applicable directly with a brush or spray gun by...
In stock
Pinion 11 teeth
Tooth height 10.5mm
Suitable for Billancourt 845cm³ engines (Type B1B and 800)
In stock
It is recommended to perform a dry fit of all body components to ensure proper alignment. Adjustments may be necessary.
Shipping available. Contact us to obtain a transport quote and find out our conditions....
In stock
1000 / R1 / R2 / R3
In stock
1000 / R1 / R2 / R3
In stock