- Allows control of nozzle calibration
- Graduation is 0.10 mm in 0.10 mm increments, with a minimum of 1.5 mm to 3.00 mm and a maximum of 1.5 mm.
In stock
Tool for timing adjustment
Reference:
48107
- Synchronizer/Synchrometer to be placed directly in the air intake horn for timing adjustment
- Suitable for all AVP air intake horns
- Graduation from 1-30kg/h
€79.00
(tax incl.)
Order before 1pm and enjoy same day shipping !
You may also like
- Allows control of nozzle calibration
- Graduation is 0.05 mm in 0.05 mm increments, with a minimum of 0.45 mm and a maximum of 1.5 mm.
In stock
- Allows easy adjustment of the float with one side of the tool calibrated to 5mm and the other to 6mm.
- Allows direct action on the float tab thanks to a slot at the end of the tool
In stock
- Allows easy adjustment of the float with one side of the tool calibrated to 8mm and the other side to 9mm.
- Allows direct action on the float tab thanks to a slot at the end of the tool.
In stock
Customers who bought this product also bought:
- Oil pan gasket: Simca 1000 Rallye / Rallye 1
- Engine block or oil pan gasket: Simca 1200S / Rallye 2 / Rallye 3
- Talbot OE Ref: 30197J / 0012853300 / 12853300
In stock
In stock
In stock
The kits are supplied with the following components:
- Cylinder Heads (x4)
- Domed Pistons (x4)
- Rings (x12)
- Pin (x4)
- Circle Clips (x8)
Dimensions of the various parts:
-
- Cylinder Head Bore Diameter: Ø 75.7mm
- Cylinder Head Flange or Top Diameter (D): Ø 89.75mm
- Cylinder Head Base Diameter (A): Ø 80mm
- Overall height including skirts of cylinder liners (C): 128mm
- Height from top of cylinder liner to base seal area (E): 94.80mm
- Shaft dimensions: Ø 20x63.5mm (Cirlip-free mounting)
- Ring thickness: 1.75mm / 2mm / 4mm (Fireproof/Sealing/Scraper)
- Base seal type: Paper gasket
Piston mounting direction: (arrow) drawn perpendicular to the axis of the piston, figure on the top of the piston. It must be oriented in the direction of engine rotation during the connecting rod's downward stroke (see manufacturer's instructions or diagram).
It is essential to check the ring end gap of each piston ring before installing them on the pistons, according to the values given by the manufacturer or in the supplied instructions.
During installation, the ring end gap must be evenly distributed around the piston circumference at 120° intervals.
In stock
- Fuel pressure gauge kit.
- Allows fuel pressure adjustment with the "King" filter REF 6825.
- Graduation from 0.20g up to 1 bar.
- With connector and clamp for 6 or 8 diameter flexible hoses.
- The pressure gauge can be removed after adjustment and the cap provided in the kit can be screwed on for greater privacy in the engine compartment.
In stock
Suitable for:
- Simca 1000 / 1200S / R1 / R2 / R3 / CG - Ref 22089M
- Renault R8 / R8G / Floride / Caravelle
- Alpine GT4 / A110 (1100Cm³ / 1300cm³)
- Matradjet
These bearings are only suitable for old generation water pumps for Renault and Alpine models, with a need for two bearings per water pump.
In stock
In stock
- Suitable for all types of WEBER 40DCOE carburetors
In stock