Best sellers
In stock
Suitable for Alpine A310 V6 with 2664cm³ PRV engine (Type 112.730): From engine No. 42816 to end of series ...
In stock
Windshield with separate power supply for left and right side heating.
Shipping available. Contact us to obtain a transport quote and find out our conditions.
Click HERE to write to us.
In stock
Capsule diameter Ø 55mm
The old-generation 65mm diameter capsules have been replaced by 55mm diameter models. The curve and mounting remain unchanged.
The operation of the vacuum advance is very important on certain...
In stock
In stock
In stock
In stock
This deflector is suitable for all wiper arms with flat arms 5 or 6mm wide and 2.5mm thick (before 1970)
This accessory allows for better support of the blades on the windshield while driving, and provides a...
In stock
In stock
Suitable for vehicles:
A310.4: VF and VE (From chassis no. 910 to the end)
A310 V6
In stock
Sheet Dimensions: Length 58cm x Width 35cm
Sheet Thickness: 1mm
Ideal for making carburetor gaskets, fuel pump gaskets, engine and gearbox gaskets (Parts subject to low temperature or pressure). Suitable for all...
In stock
F9 emulsion tube for WEBER 40DCOE and 45DCOE
Number 13 on exploded view
Also suitable for Weber carburetors: 32 DATR, 32 DRTA, 32 DMTRA, 48 DCOSP, 50 DCOSP, 55 DCOSP, 38 DCNL, 38 DCN, 40 DCNL, 40 DCOM, 45 DCO3, 45...
In stock
Fuel pressure gauge kit.
Allows fuel pressure adjustment with the "King" filter REF 6825.
Graduation from 0.20g up to 1 bar.
With connector and clamp for 6 or 8 diameter flexible hoses.
The pressure gauge can be...
In stock
Suitable for WEBER 40DCOE carburetors with spring lock,
Suitable for first-generation WEBER 40DCOEs with 55mm air intake nozzle REF 48093,
WARNING: If you are not using the 55mm air intake nozzle REF 48093, you must...
In stock
Throttle control lever for TWO WEBER 40DCOE AND WEBER 45DCOE carburetors
Allows carburetor synchronization
Suitable for R8 Gordini, Alpine A110, Simca Rallye
8mm diameter ball joint
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Thickness 0.70 mm, super-fittable
Number 66 on exploded view
Compatible with other WEBER carburetors, see below
In stock
In some configurations, Weber DCOE carburetors are positioned directly above the exhaust, which can create vapor lock problems due to heat: our AVP48010 plate can solve this problem
Plate can be covered with thermal...
In stock
This paste is suitable for petroleum-derived hydrocarbons (mineral oils, petroleum, fuel oil, leaded and unleaded gasoline, etc.), chlorinated solvents, diluted acids and bases
Replaces or is used in combination with...
In stock
In stock
In stock
Overall length: 243cm
Hand delivery to the AVP store.
No shipping.
In stock
Overall length: 221.5 cm
Sold individually
Shipping available. Contact us to obtain a transport quote and find out our conditions.
Click HERE to write to us.
In stock
Compatible with :
R8G R1134 (1108cm³ engine - Type 804) / R1135 (1255cm³ and 1296cm³ engine - Type812)
Alpine A110 1100G and 1300G/S
In stock
In stock
Length: 182mm
In stock
Out of stock
Thickness: 1.7mm (repair side)
Oblong “Lunules” type cylinder head gasket.
In stock
In stock
In stock
R4 (R1123): From 01/1971 (Chassis number from n°123915 to n°1587923)
R4 Van 5CV (R2106) from 01/1971 to 12/1975
R4 F4 5CV (R2391): From 01/1971
In stock
Suitable for:
R4 (R1120) from start to No. 954000
R4 (R1123) from start to No. 627131
R4 (R2106) from start to #24876
In stock
For 956cc engines (Type C1C-08 and 689-10) with high compression (compression ratio 9.25:1)
Suitable for:
R4
R5: TL / Société (After 1972)
In stock
Inner Diameter: Ø 220mm
Outer Diameter: Ø 247mm
Thickness: 8mm
Number of Teeth: 117 Teeth
Réf OE Renault / Alpine : 7700520332 / 0555482400 / 5554824
Suitable for vehicles:
R4 / 4L: Type R1128 / R1129 - Engine...
In stock
In stock
Out of stock
Out of stock
Triangle sold with its silentblocs (x4)
Suitable for:
A310 V6 (Phase 2): From chassis 47709 to the end of series(From 1981)
R5 Turbo 1 and 2 (8220)
Out of stock
Heater hose compatible with Alpine A310.4 (1st and 2nd Version):
A310.4 1600VE: From #1 to end of series
A310.4 1600VF: From #1 to end of series
In stock
In stock
In stock
In stock
Out of stock
In stock
Lift Features:
Double-acting gas lift
Mounting center distance: 595mm
Lift stroke: 250mm
Mounting eye diameter: Ø 8mm (x2)
Lifts must be mounted with the rod at the bottom, with the case or hood closed.
In most...
In stock
Suitable for GOTTI rims with 6mm diameter mounting holes.
Kit includes:
35mm screws x12
Aluminum cleats x12
Washers under nuts x12
Nuts x12
Note: Not suitable for GOTTI No. 7 rims
In stock
In stock
In stock
Gear knob covered in high-quality imitation leather
White and blue aluminum insert (identical to the original)
Gear knob screws onto the gear lever: M12 mounting
In stock
Suitable for WEBER 40DCOE and WEBER 45DCOE carburetors
Location at the bottom of the tank
Requires 1 piece per carburetor
Number 43 on exploded view
Diameter: Ø6mm / M6x100
In stock
For M12 banjo bolts
Number 98 on exploded view
In stock
HTX GENERATION 15W-40 is a mineral engine oil suitable for classic cars in the "young timer" category, particularly those manufactured between the 1980s and 2000s.
The excellent viscosity balance ensures low-wear...
In stock
Specific Bearings (Timing Side): Bearings without grooves on the main bearing cap side
Suitable for Billancourt Type 839 and 800 engines (From July 1972)
Bearing Dimensions:
Dimension: Original dimension (Standard)...
In stock
Delivery in France only
Product for stripping most varnishes and paints such as polyurethane, epoxy, glycerophthalic, cellulose, etc.
In stock
Average thickness of liner gaskets:
Blue 0.09mm / White 0.10mm / Red 0.12mm / Yellow 0.14mm
In stock
In stock
This lighter is suitable for:
- 4CV / Dauphine / Estafette / Juva 4 / R4 (1st model)
- Engine 622 / 668 / 670 / 670-3
Same as Ducellier: 566 / 3910 / 2175 / 4037 / 4065 / 4076 / 4094
Kit to be used with a primary...
In stock
- Sold complete with support, brass cap and fitting screwed onto the jar.
- Male outlet connection 1/2"-20UNF (12.70mm)
In stock
Out of stock
Thickness: 1.80mm (repair side)
In stock
In stock
Versatile "Sporty Driving" shock absorbers, ideal for road use and competition.Shock absorber hardness can be adjusted.The vehicle's ride height can be modified using the different positions of the spring retainer...
In stock
In stock