In stock
Best sellers
Out of stock
In stock
Countersunk head screw crosshead in black zinc-plated steel
Ideal for fixing:
Headlining
Interior trim, carpets, rugs
Rubber mats
In stock
Suitable for vehicles:
A310.4: VF and VE (From chassis no. 910 to the end)
A310 V6
In stock
Single-pin base / aligned pins
Dimensions: 8 x 20 mm
Due to the multitude of bulb types used, please check compatibility with your vehicle.
In stock
Black base
Sold without festoon bulb: Reference AVP1820
In stock
Suitable for WEBER 40DCOE, 45DCOE and IDF carburetors
Sold individually, requires 2 pieces per carburetor
Number 31 on the exploded view
Compatible with other WEBER carburetors, see below
In stock
Each kit is composed of all the color codes
In stock
Compatible with :
R8G R1134 (1108cc engine - Type 804) / R1135 (1255cc and 1296cc engine - Type812)
Alpine A110 1100G and 1300G/S
In stock
In stock
In stock
In stock
In stock
Inlet diameter: Ø 61mm
Dimension of the fitting on the carburettor: Length 115mm x Length 70mm
Out of stock
In stock
Out of stock
In stock
OE Renault Part Numbers: 7701068742 / 7701045747 / 7701020246 / 7701020006 / 7701017438 / 7701348081
Suitable for:
R5 (All models): For Ducellier, SEV Marchal, or Bosch mounting
R16 (R1156): TX / TL / TS
Simca 1200S
In stock
x1 pot of fine grain 240 lapping paste
x1 pot of coarse grain 120 lapping paste
In stock
In stock
In stock
Out of stock
In stock
In stock
In stock
In stock
In stock
Inner diameter: Ø 18mm
Outer diameter: Ø 42mm
Height: 42mm
In stock
Built-in short extensions
Straight coil terminal
Coil wire length: 50cm
We would like to point out that our spark plug wires are made with Ø 7mm silicone wire and a standard copper core (wire material), which means...
In stock
Suitable for the following vehicles:
R4: Billancourt engine 747cm³ / 782cm³ (Type 680-02) / 845cm³ (Type B1B and 800-...)
R5 (R1221 , R1391 , R1220): Billancourt engine 845cm³ (Type 800-10)
Renault OE Ref: 8557892 /...
In stock
Installation of a 10mm wide belt
A steel fret is installed on the oil seal surface for better sealing and reduced wear on the pulley.
OE Renault Ref: 7700507524 / 7700650823
In stock
In stock
In stock
In stock
With aligned mounting holes
Not compatible with FRANKANI mounting plates (offset holes)
In stock
With aligned mounting holes
Not compatible with FRANKANI mounting plates (offset holes)
In stock
Present on the dashboard:
Location for 3 pressure gauges,
Location for the "Brake Indicator" light,
Location for 2 horizontal switches or inverters.
In stock
In stock
It is mandatory to change the calipers in pairs (Right and left caliper)
In stock
Sheet Dimensions: Length 58cm x Width 35cm
Sheet Thickness: 0.25mm
Ideal for making carburetor gaskets, fuel pump gaskets, engine and gearbox gaskets (Parts subject to low temperature or pressure). Suitable for all...
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Requires 1 part per carburetor
Number 3 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Suitable for:
A110.1600 VD and VH (SC / SI / SX)
A310.4(All models)
A310 V6 (From #1 to #47709)
In stock
In stock
In stock
Plastic ring dimensions: Ø 22x31.5mm
Plastic ring width: 14.5mm
Kit contents:
Plastic guide ring x1
Rubber sealing gasket x2
Steel washer x2
Internal circlip x1
Renault OE Ref: 7701455252
In stock
In stock
In stock
Diameter on the rack side: M12x100 (Right hand thread)
Diameter on the steering ball side: M14x150 (Right hand thread)
In stock
It is mandatory to change the calipers in pairs (Right and left caliper)
In stock
Out of stock
In stock
Segment Characteristics:
Segment Diameter:Ø 58mm
Thickness of Upper Segments (Fire-resistant): 1.75mm
Thickness of Intermediate Segments (Waterproof): 2mm
Low ring thickness (Scraper): 3.5mm
It is essential to...
In stock
Tie rod adjustment range: 9.5cm to 11.5cm
The tie rod can be cut to size to make it shorter
In stock
Diameter of the 3 holes for the strike plate mounting screws: M8x100
In stock
Out of stock