Suitable for all types of WEBER 40DCOE carburetors
In stock
Best sellers
Aluminum air intake horn/trumpet for WEBER 40DCOE carburetor
43mm extension over the carburetor
Stud/nut mounting
Allows installation of high-performance filter REF 48099 or 48100
Also suitable for AVP sock filter...
Out of stock
Air intake trumpet/trumpet for WEBER 45DCOE
carburetor,
Protrusion length from the carburetor: 62mm,
ATTENTION: Must be mounted with venturi REF 48086,
Mounting kit REF 48098,
Suitable for mounting AVP filters ref...
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Thickness 0.70 mm, super-fittable
Number 66 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors old generation for the throttle screw,
Suitable for all types of WEBER 40 and 45 DCOE carburetors for the inspection hatch,
Sold individually,
Countersunk head and...
In stock
Suitable for WEBER 40DCOE and WEBER 45DCOE
Sold individually, need 2 pieces for one carburetor
Number 64 on exploded view
Also suitable for the following carburetors: 32 DCOF, 38 DCOE, 40 DCO3, 40 DCOE, 42 DCOE, 45...
In stock
Identique aux cabochons de marque YORKA et SEIMA
In stock
Delivery in France only
Product for stripping most varnishes and paints such as polyurethane, epoxy, glycerophthalic, cellulose, etc.
In stock
In stock
In stock
In stock
In stock
In stock
Segment Characteristics:
Segment Diameter: Ø 75.70mm
Thickness of Upper Segments (Fire-resistant): 1.5mm
Thickness of Intermediate Segments (Waterproof): 2mm
Low ring thickness (Scraper): 4mm
It is essential to...
In stock
For mounting a belt width: 13mm
Groove for a 5mm key
A steel collar is installed on the oil seal surface for improved sealing and reduced pulley wear.
In stock
R4 (R1123): From 01/1971 (Chassis number from n°123915 to n°1587923)
R4 Van 5CV (R2106) from 01/1971 to 12/1975
R4 F4 5CV (R2391): From 01/1971
In stock
Suitable for:
R4 (R1120): From start to chassis no. 468774
R4 (R1123): From start to chassis no. 212514
Renault OE Ref: 0996027700 (Left) + 0996027600 (Right)
Steering Ball Joint Pin : M10
In stock
For 956cc (Type C1C-08 and 689-10) high compression engine (Compression ratio 9.25:1)
Suitable for:
R4
R5: TL / Company (After 1972)
The kits are supplied with the following:
Crankcases (x4)
Pistons (x4)
Rings...
In stock
In stock
In stock
In stock
Out of stock
Center distance between carburetor and intake pipe : 110mm and 70mm
Ideal assembly with a pair of aluminium flanges Ref: AVP6810
Out of stock
In stock
Suitable for Alpine A310 V6 with 2664cm³ PRV engine (Type 112.730): From engine No. 42816 to end of series ...
In stock
In stock
In stock
Thickness of the pressure disc: 6.95mm / 7.00mm
Thickness of the disc in the rest position: 7.70mm
In stock
In stock
Oil pan depth: distance from the gasket surface to the bottom of the pan 147mm
Sold with gasket and drain plug (x3).
In stock
Single-pin base / aligned pins
Dimensions: 9 x 28 mm
Due to the multitude of bulb types used, please check compatibility with your vehicle
In stock
In stock
Upright height: 30cm
Sold individually
In stock
Adaptable leather gear knob with visible stitching
Knob dimensions:
Knob diameter: Ø 47.5mm
Knob height: 60mm
Supplied with 3 different tips to fit all types of levers (screwed or glued):
Chrome screw-on tip:...
In stock
Grease nipple with steel ball
Grease nipple (overall) height: 24mm
Grease nipple with a 9 key
In stock
For cold start system/automatic choke for Solex 34 TBIA carburetor
Ref OE Origine : 7701022979, 7701019169
In stock
Kit includes: 4 screws, 8 washers, and 4 nuts
This kit allows you to install an aluminum shim on the pivot (right or left),
2 kits required per vehicle.
In stock
Suitable for:
Floride S and Caravelle (R1131 / R1133): 1108 cc engine (Type 688-01 / 688-02 / 688-03) and 956 cc engine (Type 689-01 / 689-02 / 698-03)
R8 / R8 Majeure (R1130 / R1132): 1108 cc engine (Type 688-01 /...
In stock
In stock
F9 emulsion tube for WEBER 40DCOE and 45DCOE
Number 13 on exploded view
Also suitable for Weber carburetors: 32 DATR, 32 DRTA, 32 DMTRA, 48 DCOSP, 50 DCOSP, 55 DCOSP, 38 DCNL, 38 DCN, 40 DCNL, 40 DCOM, 45 DCO3, 45...
In stock
Air bypass screw locking nut for carburettor WEBER 40DCOE and 45DCOE
M5
Number 27 On exploded view
Also suitable for: 36 DCNF 36 DCNFA 40 / 45 DCOE 40 IT
In stock
Air bypass screw for carburettor WEBER 40DCOE and 45DCOE
Number 26 On exploded view
Also suitable for the following carburettors: 36 DCNF 36 DCNFA 40 / 45 DCOE 40 IT .
In stock
Suitable for WEBER 40DCOE AND 45DCOE carburetors
This fits on the side opposite the throttle control
Part number 86 on exploded view
Also suitable for: 30 IBA, 32 IBA, 36 DCNF, 36 DCNFA, 36 DCNV, 36 DCNVA, 38 DCOE,...
In stock
The kit consists of:
"T" fuel connector x1
90° elbow fuel connector x1
Banjo connector screw x2
Banjo screw under head seal x2
Banjo screw lower seal x2
Hose clamp: Size 12-14mm x3
Out of stock
Plastic tank designed to withstand modern gasolines (replacing Manolene tanks)
In stock
Compatible with :
R8G R1134 (1108cm³ engine - Type 804) / R1135 (1255cm³ and 1296cm³ engine - Type812)
Alpine A110 1100G and 1300G/S
In stock
In stock
Length: 182mm
In stock
Out of stock
Thickness: 1.80mm (repair side)
In stock
Diamond Dimensions:
Height: 34 mm
Width: 22 mm
One mounting stud: Ø 4 mm
In stock
Versatile "Sporty Driving" shock absorbers, ideal for road use and competition.
Shock absorber hardness can be adjusted.
The vehicle's ride height can be modified using the different positions of the spring retainer...
In stock
In stock
In stock
Segment Characteristics:
Segment Diameter: Ø 74.50mm
Thickness of Upper Segments (Fire-resistant): 1.50mm
Thickness of Intermediate Segments (Waterproof): 2mm
Low ring thickness (Scraper):4mm
It is essential to...
In stock
In stock
Segment Characteristics:
Segment Diameter: Ø 77.5mm
Thickness of Upper Segments (Fire-resistant): 1.75mm
Thickness of Intermediate Segments (Waterproof): 2mm
Low ring thickness (Scraper): 4mm
It is essential to...
In stock
In stock
Out of stock
Out of stock