Out of stock
Best sellers
In stock
Front hose length: 505mm
Rear hose length: 270mm
In stock
In stock
Œil de fixation inférieur largeur : 21mm
Diamètre intérieur d'œil de fixation inférieur : Ø 9mm
In stock
Thickness: 1.35mm (Standard)
In stock
Out of stock
Overall length: 174.5 cm
Sheath length: 145 cm
Cable length: 167.5 cm
Our cables are made in France and meet the assembly and quality standards of original equipment (OEM) cables from automotive manufacturers.
In stock
In stock
In stock
Out of stock
Dimensions of the Large Spring:
Outer Diameter: Ø 33.3mm
Inner Diameter: Ø 25mm
Wire Diameter: Ø 4.1mm
Free Height (overall): 44.40mm
Dimensions of the Small Spring:
Outer Diameter: Ø 23.3mm
Inner Diameter: Ø...
In stock
In stock
Spacer to be positioned on the carburetor studs or carburetor anti-vibration spacers
Silent block specifications:
Silent block inner diameter: Ø 8mm
Silent block outer diameter: Ø 15.5mm
Height (overall): 9.5mm...
In stock
Inner diameter of the rubber washer: Ø 95mm
Outer diameter of the rubber washer: Ø 125mm
In stock
Single-pin base / aligned pins
Dimensions: 9 x 28 mm
Due to the multitude of bulb types used, please check compatibility with your vehicle
In stock
Blue silicone ignition harness with 90° angled terminals (long extensions integrated into the wires)
This ignition harness consists of 4 spark plug wires and one coil wire.
Terminals on coil 90° angled
Length of coil cable: 61cm
Length of 2 spark plug wires: 26.5cm
Length of 2 spark plug wires: 36.5cm
We would like...
In stock
Neoprene-type contact adhesive in spray form, extra-strong. It adheres to many materials such as leather, fabrics, plastic, woodwork, etc. Allows simple, rapid, precise, and durable bonding of materials. Applies as a...
In stock
The entire kit is made up of 3/8" -24UNF fittings
This kit is made up of the following copper pipes:
- from the brake master cylinder to the Front Right wheel
- from the brake master cylinder to the Front Left wheel
-...
In stock
Suitable for (Engine Type 688 / 689 / 810):
R4 / R6 / R8
Caravelle - Matra Jet
R12.TL - R12.TS - R15.TL
A110.V85 (810) - A110.GT4
This distributor must be used with a coil with a primary resistance between 2.5...
Out of stock
Suitable for:
- Front brake for "Big front brake" type mounting: A110/R8G
- Rear brake for "Big Rear brake" type with hydraulic handbrake: A110/R8G
- Front brake: A310.4 (from chassis n°910 to end of series)
- Front...
In stock
In stock
It is recommended to perform a dry fit of all body components to ensure proper alignment. Adjustments may be necessary.
Shipping available. Contact us to obtain a transport quote and find out our conditions....
In stock
It is recommended to perform a dry fit of all body components to ensure proper alignment. Adjustments may be necessary.
Shipping available. Contact us to obtain a transport quote and find out our conditions....
In stock
In stock
Mounting hole spacing: 55mm
Suitable for the following vehicles:
R4 / 4L
RODEO
In stock
In stock
Alpine OE Ref: 7910246036 / 7910246590
In stock
Alpine OE Ref: 7700268487 / 7700268726
In stock
Grid mesh identical to the original
Grid dimensions:
Length:45cm
Height:15.5cm
Curve:3.5cm
In stock
In stock
In stock
Chain 72 links
Adjustable 36 tooth sprocket and 18 tooth sprocket
Out of stock
Suitable for: R5 Alpine (R1223) and R5 Alpine Turbo (R122B)
Double Chain: 58 Links ( OE Renault Ref 7701348715 )
Crankshaft Sprocket: 17 Teeth ( OE Renault Ref 7700590313 )
Camshaft Sprocket: 34 Teeth ( OE Renault...
This harness uses the color codes of the original wires and terminals,
Original gray ribbon,
Harness sold with its installation plan, all the connectors are identified and labeled.
Harness for assembly with original...
In stock
In stock
Diameter of the threaded supply connection: Ø 3/8" - 24UNF (+/- 9.52mm)
In stock
Door switch with metal body for turning on the ceiling light
Door switch diameter: Ø 10mm
Switch length (overall): 31mm
In stock
Sheet Dimensions: Length 50cm x Width 35cm
Sheet Thickness: 1.2mm
Ideal for making water seals, oil pumps, cylinder head cover gaskets, oil pan gaskets, and intake or exhaust manifold gaskets. Temperature limit:...
In stock
Sheet Dimensions: Length 50cm x Width 33cm
Sheet Thickness: 2mm
Ideal for making oil pan gaskets, timing case gaskets, and cylinder head cover gaskets. These gaskets must be installed with a light clamping force....
In stock
Suitable for WEBER 40DCOE carburetor
Protrusion length from the carburetor = 25mm
Stud/nut mounting
Allows the installation of high-performance filters REF 48099 or 48100
Also suitable for AVP sock filter ref 48103...
In stock
Allows to clamp the horns on the body of the WEBER 40DCOE carburetor
ATTENTION: essential for REF 48093 horns
Kit for a carburetor consisting of 4 stop tabs, 4 washers and 4 nuts
Also suitable for WEBER 42DCOE...
In stock
Suitable for WEBER 40DCOE AND 45DCOE carburetors
This fits on the side opposite the throttle control
Part number 86 on exploded view
Also suitable for: 30 IBA, 32 IBA, 36 DCNF, 36 DCNFA, 36 DCNV, 36 DCNVA, 38 DCOE,...
In stock
Suitable for engines:
Alpine A310 V6: PRV 112.730 engine
Alpine V6 GT (D500): Z6W engine
Alpine V6 Turbo (D501 and D502) and Renault 25: Z7U engine
Bearing dimensions:
Dimension: Stock dimension (Standard)
Journal...
In stock
Pair of Right and Left Steering Tie Rods - R4 (Third Models - From 1969 to 1978) / R5 (First Models)
Suitable for:
R4 (R1120): From chassis no. 954001 to the end
R4 (R1123): From chassis n°627132 to n°2012576
R4 (R1126): From the beginning to chassis no. 655996
R4 (R1128): From the beginning to chassis no. 60549
R4...
In stock
Bearing Dimensions:
Dimension: Repair Dimension (+0.20)
Journal Diameter (A): Ø 51.47mm
Housing Diameter (B): Ø 55.88mm
Bearing Width (C): 18.68mm
Bearing Width (C): 24.68mm
Bearing Thickness (D): 2.17mm
Smooth,...
In stock
In stock
In stock
Adjustable shock absorber stiffness.
Versatile "Road" shock absorbers, ideal for road use and competition.
Detailed description of Koni shock absorbers, see below
In stock
In stock
This harness uses the color codes of the original wires and terminals
Harness sold with its installation plan, all the connectors are identified and labeled
Harness for mounting with original terminal boxes or modern...
In stock
The sets are supplied with the following components:
Liners (x4)
Pistons (x4)
Segments (x12)
Axles (x4)
Dimensions of the individual parts:
Liner bore diameter: Ø 79mm
Liner collar or top diameter (D): Ø 96mm...
In stock
Segment Characteristics:
Segment Diameter:Ø 78mm
Thickness of Upper Segments (Fire-resistant): 1.75mm
Thickness of Intermediate Segments (Waterproof): 2mm
Low ring thickness (Scraper): 4mm
It is essential to...
In stock
Overall length: 153cm (x2)
Sheath length: 131cm (x2)
Cable length: 150cm (x2)
Suitable for:
R4 TL/ GTL / CLAN (R1128): From chassis no. 390246 to the end of the series...
R4 F4 (R210B): From chassis no. 15201 to...
In stock
Overall length: 191 cm
Sheath length 1: 82 cm
Sheath length 2: 78 cm
Cable length: 187.5 cm
Our cables are made in France and meet the assembly and quality standards of original equipment (OEM) cables from...
In stock
In stock
Out of stock
34-tooth sprocket for single chain timing chain
In stock
This ignition harness consists of 4 spark plug wires and one coil wire.
Terminals on coil straight
Length of coil cable: 61cm
Length of 2 spark plug cables: 26.5cm
Length of 2 spark plug cables: 36.5cm
We would like...
In stock
Alpine OE Ref: 6001001240
For A310 V6 (After 1981 - From chassis number 47709 onwards)
Two tubes required per car
Tube length: 33cm x 23cm
In stock
Sheet Dimensions: Length 58cm x Width 35cm
Sheet Thickness: 1mm
Ideal for making carburetor gaskets, fuel pump gaskets, engine and gearbox gaskets (Parts subject to low temperature or pressure). Suitable for all...
In stock
Lift Features:
Double-acting gas lift
Mounting center distance: 595mm
Lift stroke: 250mm
Mounting eye diameter: Ø 8mm (x2)
Lifts must be mounted with the rod at the bottom, with the case or hood closed.
In most...
In stock