In stock
Best sellers
In stock
Out of stock
Original type screw with slotted recess
In stock
In stock
In stock
In stock
3 x Fittings: Ø 3/8"-24UNF (Ø 9.52mm)
2 x Mounting Holes
Suitable for:
R4 / 4L: From 1968 to 1976
R5 TL / R5 TS
R16 TS
Out of stock
Hollow piston
Banjo fixing screw: Ø7/16" - 20UNF (inside Ø 10mm)
In stock
Out of stock
Suitable for:
Alpine A310 V6: From chassis number 47709 to end of series
Alpine GTA: V6 GT (D500) and V6 Turbo (D501 / D502)
Alpine A610 (D503)
In stock
Out of stock
Out of stock
Suitable for:
Simca Coupé 1000: Disc brake
Simca 1200S (Before 1970) / CG: Disc brake
Bearing dimensions: Ø 27x50.3x14.2mm and Ø 17.45x39.9x14.55mm
Oil seal dimensions: Ø 38x52x8mm
In stock
In stock
Supplied with 4 carburetor mounting studs
Carburetor mounting stud distance: 110mm and 70mm
The carburetor is mounted directly onto the manifold. A seal is ensured by two paper gaskets; there is no need to use...
In stock
In stock
Alpine OE Ref: 7700268487 / 7700268726
In stock
In stock
Piston pin Ø 21x69x12mm
In stock
In stock
Mounting center distance (Width): 48.5mm
Mounting center distance (Length): 92mm
Thickness: 5mm
In stock
Out of stock
In stock
Fixing distance: 45mm
Thickness:5mm
In stock
In stock
Delivered without fuses
Dimensions: Lg 122mm x W 47mm x H 27mm - Fixing distance: 90mm
In stock
Suitable for:
- R4 - R6 - R8 - Caravelle - Matra jet - R12.TL - R12.TS - R15.TL - A110.V85 (810) - A110.GT4
- Type 688 / 689 / 810 engine
This igniter is to be used with a primary resistance coil between 2.5 and 3.5...
In stock
Delivery in France only
Anti-corrosion paint for engine block, crankcase, brake drum, and gearbox.
Resistant to 180°C
Capacity: 500ml
Color: Bright Blue RAL 5005
Applicable directly with a brush or spray gun by...
In stock
In stock
In stock
782 cc / 839 cc / 706 cc engine from 1972 to 1982
Engine 845 cc / 800 - 7 - B1B from 07/1967 to 06/1986
In stock
Suitable for valves with a groove in the lower position (type BK) and for stems with a diameter of 7mm
Out of stock
In stock
Suitable for:
- R8.G (R1134 / R1135) from 10/1964 to 1974
- Alpine A110: 1100cc / 1300cc / 1600cc / SC and SX (with Alpine A310 rear axle)
- Alpine GT4 / Matradjet
In stock
Possible mounting on the 4CV / Dauphine and Dauphine Gordini cylinder head (aligned or offset mounting holes)
Intake manifold inner diameter: Ø 29mm
Exhaust manifold inner diameter: Ø 29mm
Outlet inner diameter: Ø...
In stock
In stock
Length under head: 25mm
Overall length: 30mm
Suitable for:
A310.4: From chassis no. 1 to no. 634 (1st model)
In stock
Sold with screws, washers, and nuts.
In stock
Air intake trumpet filter for WEBER 45DCOE carburetor
Fitment possible on all AVP trumpets
Mesh filters that feature two layers of stainless steel mesh with a filter layer in between to ensure maximum engine...
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors,For 23g or 26g brass or plastic float,Requires 1 piece per carburetor,Number 72 on the exploded view,Also suitable for the following carburetors: DCOE, DCO/SP, 40DCZ,...
In stock
In stock
The entire kit is made up of 3/8"-24UNF fittings
This kit is composed of the following copper pipes:
- From the brake master cylinder to the Right Front Wheel
- From the brake master cylinder to the Left Front Wheel
-...
In stock
The entire kit is made up of 3/8" -24UNF fittings
This kit is made up of the following copper pipes:
- from the brake master cylinder to the Front Right wheel
- from the brake master cylinder to the Front Left wheel
-...
In stock
In stock
Compatible with 1565cm³ to 1647cm³ engines (Type 807 , 844 and 843):
A110 1600S/SC/SX
A310 1600cc
R12G / R17G
R16.TS/TX
In stock
In stock
Delivery in France only
Using the measuring cap, simply mix the concentrated windshield washer fluid directly with water.
250ml bottle = 25 liters of windshield washer fluid
In stock
In stock
In stock
4L: R1123/ R1125 / R1129 / R2106 / R2391 / R2392 from 1976 to 1982 4L: R1123 / R 2106 / R2391 after 1983
In stock
Out of stock
In stock
In stock
In stock
Out of stock
In stock