Best sellers
Special Premium Quality graphite for clutch release bearings
Important: The release bearing clamping screw must be placed on the side opposite the fork
Depending on the diameter of the return spring, it may be...
Out of stock
A M12x175 screw is required to secure the axle to the support.
In stock
In stock
Supplied with 2 banjo bolts: M12x100 and 4 copper gaskets.
Compatible with the following vehicles:
A310.4: From chassis no. 635 to end of series (With 2nd assembly clutch slave cylinder)
A310 V6: All models
In stock
sold by pair
In stock
In stock
In stock
In stock
Suitable for vehicles:
4CV / Juvaquatre: Type 662 Engine (From June 1956)
Dauphine / Dauphinoise / Estafette / Floride A106 / A108: Type 670 Engine
R4: Billancourt Type 800-02/05 Engine (From 1962)
Bearing...
In stock
Stem length: 37mm
Membrane mounting hole spacing: 27mm
Cup diameter 1: Ø 8.20 mm
Cup diameter 2: Ø 10.20 mm
In stock
R12 TS: Double body carburettor 32 DIR / ref: 7700577132
A110.V85
In stock
Tie rod/ball joint thread: M14x150(Left-hand thread)
Tie rod sold individually
It is possible to install it on an A310.4 using the AVP7609 adapter to replace the original "fork"-type tie rods
The AVP7606 tie rod is...
In stock
Thickness: 1.2mm (Original side)
Oblong “Lunules” type cylinder head gasket
In stock
Grid mesh identical to the original
Grid dimensions :
Length : 57cm
Height : 20cm
Curve : 7cm
In stock
In stock
Comes with its silentbloc
Hardness of the rubber of the silentbloc: 75 Shores
In stock
Comes with its silentbloc
Hardness of the rubber of the silentbloc: 75 Shores
In stock
In stock
Out of stock
Out of stock
Out of stock
In stock
In stock
In stock
In stock
The set of rings is ready to install, only the lubrication hole must be drilled after installing the rings in the block.
Ring dimensions:
x2 rings Ø37.90x41.445mm
x2 rings Ø37.90x41.00mm
Renault OE Ref: 0855569000...
Out of stock
Sold individually, 16 pieces per engine (8 pieces per cylinder head) required
Screw dimensions:
Thread: M12
Screw pitch: 1.5 mm
Length under head: 178 mm
Screw head: Hexagonal
In stock
Compatible avec :
R8G R1134 (Moteur 1108cm³ - Type 804) / R1135 (Moteur 1255cm³ et 1296cm³ - Type 812)
Alpine A110 1108cm³ / 1289cm³ (V85) / 1300G / 1300S
R5 Turbo 1 et 2 (1397cm³) / R5 Alpine Turbo / R5 Alpine...
In stock
Can be used with:
- the AVP4723 thermistor
- a thermal contact AVP4724 or AVP1744
In stock
In stock
Out of stock
In stock
Suitable for GOTTI rims with machining to accommodate wheel nut inserts
For cone 60° nuts
Made of durable zinc-plated steel
Inner diameter: Ø 13mm
Outer diameter: Ø 16mm
Outer shoulder diameter: Ø 25mm
In stock
In stock
In stock
Suitable for:
R5 Turbo 1 and 2 (8220)
A310 V6 - After 1980(From #47709 to the end of the series)
Alpine GTA: V6 GT (D500) and V6 Turbo (D501 and D502): Rear brake caliper
Kit contents:
Spring clips: x4
Retaining...
In stock
Renault 4 version: L / TL / GTL
Renault 5 version: L / TL / GTL
In stock
The position of the groove for securing the half-moon valve keepers must be checked.
Valve angle : 45°
Keying type (Half-moon valve keeper): KK (x1 Round groove)
Renault / Alpine OE part number: 7701458180 /...
In stock
- Sold complete with support, brass cap, insert and rubber teat
- Jar mounted with rubber teat Ø 6mm
In stock
Can also fit on Caravelle and Floride S trumpets
In stock
Douille en bout de la manivelle pour écrou de roue : 17mm
In stock
In stock
For the Alpine A108: Consult us before placing the order because several assemblies are possible.
In stock
Lower fixing eye width 25.8mm
Lower fixing screw Ø 10mm
In stock
In stock
In stock
In stock
The position of the groove for securing the half-moon valve keepers must be checked.
Valve angle : 45°
Keying type (half-moon): MK (x2 round groove)
Renault / Alpine OE part number: 7701458690
Suitable for:
R4:...
In stock
Suitable for:
R8 / A110: Front Big Brakes
R5 Alpine Atmo (1223) and Alpine Turbo (122B): Front Brakes
A310.4: Front Brakes
A310 V6 (Pre-1980): Front Brakes
R12 (All models): Front Brakes
R15 / R16 / R17 (All...
In stock
Please note this hose cannot replace the original oil hoses, use only to carry out an adaptable assembly using a connector and a new radiator.
Material: Black synthetic braid
Maximum operating pressure 35 bar and...
In stock
In stock
Connection thread: outgoing cone
Fixing center distance: 31mm
OE Renault Ref: 0870056500 / 7701000525 / 7701365089 / 7701366377
In stock
Suitable for (Engine type 662 / 668 / 670 / 670-3):
4CV / Dauphine
Estafette / Juvaquatre
Identical to Ducellier: 566 / 4054 / 4037
Replaces SEV Marchal distributor K4 A46, RB U4VA (SEV Junior)
Curve designed for...
Out of stock
In stock
In stock
Out of stock
In stock
In stock
