In stock
Best sellers
Cap Dimensions:
Inner Diameter: Ø 47mm
Outer Diameter: Ø 49.5mm
Height: 23mm
In stock
In stock
In stock
In stock
3-tube pump: Inlet - Outlet - Return
Sold without seal and without thermal shim
In stock
Suitable for:
R5 Alpine Coupe / GR2 : Front Brake
R12G / R17G : Front Brake
R15.TS / R17TS / R17TL : Front Brake
R16.TX (1st assembly) : Front Brake
A310.4 (n°1 to n°909) : Front Brake
In stock
In stock
In stock
Overall Length: 236cm
Sheath Length: 193.5cm
Cable Length: 226cm
Our cables are made in France and meet the assembly and quality standards of original equipment (OE) cables from car manufacturers.
In stock
In stock
In stock
In stock
Overall length: 64 cm
Sheath length: 45 cm
Cable length: 55 cm
Our cables are made in France and meet the assembly and quality standards of original equipment (OEM) cables from automotive manufacturers.
In stock
Out of stock
Overall length:209cm
Sheath length:186cm
Cable length:198.5cm
Suitable for cars with a handbrake under the dashboard:
A110.1600 VB and VC
Our cables are made in France and meet the assembly and quality...
In stock
In stock
Out of stock
In stock
Out of stock
In stock
In stock
Suspension ball joints: M12x125 axle - Cone Ø 15mm to Ø 17.5mm
Mounting center distance on the wishbone: 46mm and 54mm
Out of stock
In stock
In stock
For gearbox control shaft Ø 13mm
Suitable for gearboxes: 330-A4 / 353 / 364-05 / 364-06
OE Renault Ref: 98079333 / 0980793300 / 7701455390 / 7701501597
In stock
In stock
Please note this hose cannot replace the original oil hoses, use only to carry out an adaptable assembly using a connector and a new radiator.
Material: Black synthetic braid
Maximum operating pressure 35 bar and...
In stock
Plate surround fixing clip not supplied see Ref AVP49105
In stock
In stock
Dimension of the axis of the upper fixing bolt at the support of the 1st washer
In stock
Cooling hose compatible with Alpine:
A310.4 1600VE: From #1 to end of series
A310.4 1600VF: From #1 to end of series
A110 SC / Si (1600VD) and SX (1600VH)
In stock
Plate comes complete with mounting hardware.
Black cataphoresis treatment for optimal finish and corrosion resistance.
In stock
In stock
A M12x175 screw is required to secure the axle to the support.
In stock
In stock
In stock
For piston kit liners Ø 79mm (AVP6085) and Ø 77.8mm (AVP60134)
In stock
In stock
Connection: Male / Male Ø 11/16"-16UNF (Ø 17.16mm)
Length: 18.5cm (Overall)
In stock
Filetage de la vis de fixation du bandjo: Ø 7/16"- 20UNF (Ø 11.11mm)
In stock
Out of stock
1-pin base / aligned pins
Dimensions: 18x37mm
Part Number: 0802802200
Due to the multitude of bulb types used, please check compatibility with your vehicle.
In stock
Out of stock
R12 TS: Double body carburettor 32 DIR / ref: 7700577132
A110.V85
In stock
In stock
In stock
sold by pair
In stock
Special Premium Quality graphite for clutch release bearings
Important: The release bearing clamping screw must be placed on the side opposite the fork
Depending on the diameter of the return spring, it may be...
In stock
In stock
The set of rings is ready to install, only the lubrication hole must be drilled after installing the rings in the block.
Ring dimensions:
x2 rings Ø37.90x41.445mm
x2 rings Ø37.90x41.00mm
Renault OE Ref: 0855569000...
Out of stock
In stock