Out of stock
Carburetor & Carburetor Parts R8/ R8S / R8G
Carburetors and carburetor parts for Renault R8, R8S, and R8 Gordini
Restore the power to your Renault R8, R8S, or R8 Gordini with our range of carburetors and their fuel systems. Whether you're in the middle of a restoration or performing routine maintenance, you'll find reliable and perfectly adapted parts here.
A complete selection of carburetor spare parts:
- High-performance Weber 40 DCOE and 45 DCOE carburetors, specially adapted for Renault R8 Gordini and sports tuning
- Fuel pumps, including original SEV models for optimal flow
- Flanges and adapters for Weber DCOE carburetors, custom aluminum manifolds
- O-rings and specific Weber 40/45 DCOE gaskets to ensure a perfect seal
- Floats, needles, and Calibrated jets for Weber DCOE 40 and 45 carburetors
- High-quality fuel filters compatible with Weber DCOE-equipped systems
- Reinforced hoses and copper tubes suitable for Weber high pressure systems
- Accelerator pumps and adjustment accessories for Weber 40 and 45 DCOE
- Specific Weber DCOE accessories: screws, levers, diaphragms, and adjustment parts
- Tank treatment and cleaning to preserve fuel quality in Weber systems
All our parts are selected to ensure a good air/fuel mixture and efficient carburetion, meeting the requirements of classic R8 engines such as Gordini.
Trust AVP to find quality carburetor spare parts, tested in our restoration workshop.
Out of stock
In stock
In stock
In stock
In stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
M5X22 screws
Sold individually, requires 9 pieces for one carburetor
Number 5 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Number 83 on exploded view
In stock
Lower bowl cover gasket ref 48110 for WEBER 40DCOE and 45DCOE
Number 36 on exploded view
In stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors,For 23g or 26g brass or plastic float,Requires 1 piece per carburetor,Number 72 on the exploded view,Also suitable for the following carburetors: DCOE, DCO/SP, 40DCZ,...
In stock
In some configurations, Weber DCOE carburetors are positioned directly above the exhaust, which can create vapor lock problems due to heat: our AVP48010 plate can solve this problem
Plate can be covered with thermal...
In stock
In stock
In stock
In stock
In stock
For M12 banjo bolts
Number 70 on exploded view
In stock
For M12 banjo bolts
Number 98 on exploded view
In stock
M12 Banjo Bolt
Sold individually without gasket
Number 70 on exploded view
In stock
Banjo screw M12
Sold individually without gasket
In stock
Gasket dimensions: Ø 20x12x1mm
Suitable for WEBER 40DCOE and 45DCOE carburetors
Number 2 and number 69 on exploded view
Sold individually, 1 piece required for one carburetor
Compatible with other WEBER carburetors,...
Out of stock
Joint dimensions: Ø 20x16x1mm
In stock
The kit consists of:
"T" fuel connector x1
90° elbow fuel connector x1
Banjo connector screw x2
Banjo screw under head seal x2
Banjo screw lower seal x2
Hose clamp: Size 12-14mm x3
In stock
The kit consists of:
90° elbow fuel connector x1
Banjo connector screw x1
Banjo screw under head gasket x1
Banjo screw lower gasket x1
Hose clamp: Size 12-14mm x1
In stock
Sold individually, 1 required per carburetor,
Number 4 on exploded view
In stock
In stock
Suitable for WEBER 40DCOE and WEBER 45DCOE carburettor
Thread16x1.5
Need 1 piece for a carburetor
Number 1 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Requires 1 part per carburetor
Number 3 on exploded view
Compatible with other WEBER carburetors, see below
In stock
In stock
In stock
In stock
Renault OE Ref: 85295330 / 0857734900
Suitable for:
R8 (R1130 / R1132): Solex 32 DISTA / DITA
Caravelle: Solex 32 DISTA / DITA
In stock
This hose is also suitable for carburetors with a cold-start choke controlled by a thermostatic spring heated by hot water (Hose from the cold-start heater to the carburetor base)
OE Renault Ref: 8575004 / 0857735000...
In stock
Delivered with these O-rings (x4) and these paper seals (x4)
In stock
Pipe delivered with 2 O-rings and 4 carburetor mounting studs
The carburetor is mounted directly on the pipe, the seal is ensured by 2 O-rings, it is not necessary to use flexible or rigid flanges.
In stock
In stock
In stock
In stock
In stock
Manifold comes with 4 O-rings and 8 carburetor mounting studs
Intake manifold height: 76mm
The carburetor mounts directly onto the manifold. Four O-rings ensure a tight seal; there's no need to use flexible or rigid...
In stock
In stock
In stock
Levier de commande d'accélérateur pour UN carburateur WEBER 40DCOE ET 45DCOE
Adaptable sur R8 et Alpine A110 avec pipe pour un carburateur WEBER
Dimension du centre de l'arbre au centre de la rotule: 23,50 mm
Rotule...
In stock
Throttle control lever for TWO WEBER 40DCOE AND WEBER 45DCOE carburetors
Allows carburetor synchronization
Suitable for R8 Gordini, Alpine A110, Simca Rallye
8mm diameter ball joint
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
M5x32 screw
Head width 8mm
Number 52 on exploded view
Compatible with other WEBER carburetors, see below
In stock
In stock
In stock
In stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
External mounting
Fixes to the carburetor cover
In stock
This bracket attaches to the gearbox studs.
In stock
Suitable for WEBER 40DCOE carburetor
Extension length from the carburetor = 25mm
Stud/nut mounting
Allows the installation of high-performance filters REF 48099 or 48100
Also suitable for AVP stock filter ref 48103...
In stock
Aluminum air intake horn/trumpet for WEBER 40DCOE carburetor
43mm extension over the carburetor
Stud/nut mounting
Allows installation of high-performance filter REF 48099 or 48100
Also suitable for AVP sock filter...
In stock
Air intake horn/trumpet for WEBER 40DCOE carburetor
Extension length from the carburetor: 55mm
ATTENTION: Must be fitted with venturi REF 48084 or 48085
Fixing with kit REF 48097
Suitable for fitting AVP filters ref...
In stock
Allows to clamp the horns on the body of the WEBER 40DCOE carburetor
ATTENTION: essential for REF 48093 horns
Kit for a carburetor consisting of 4 stop tabs, 4 washers and 4 nuts
Also suitable for WEBER 42DCOE...
In stock
Fits WEBER 40DCOE first and latest generation carburetors
This spacer is required if you are using the REF 48084 or REF 48085 venturis without the AVP 55mm air intake nozzles, part number 48093
It fills the gap...
In stock
In stock
In stock
In stock
Air intake horn/trumpet filters for WEBER 40DCOE carburetor
Fitment possible on all AVP air intake horns
Mesh filters that feature two layers of stainless steel mesh with a filter layer in between to ensure maximum...
In stock
Suitable for Cornet/Air intake trumpet of the Weber DCOE 40 carburetor,
Fixing by screw necklace on rubber flange for perfect sealing,
Possible assembly on all AVP cornets for DCOE40,
Overall length: 115mm,
Diameter:...
In stock
Installation possible on all AVP horns
Length 115mm (can be cut to size)
Clamp included
Sold in pairs
In stock
Suitable for WEBER 40DCOE carburetors with spring lock,
Suitable for first-generation WEBER 40DCOEs with 55mm air intake nozzle REF 48093,
WARNING: If you are not using the 55mm air intake nozzle REF 48093, you must...
In stock
Suitable for Latest generation WEBER 40DCOE carburetor with 55mm air intake nozzle REF 48093
WARNING: If you are not using the 55mm air intake nozzle REF 4093, you must use the spacer REF 48087 to fill the gap...
In stock
Kit of 4 springs for locking the venturi in the body of the WEBER DCOE 40 and DCOE 45 carburetor
For first generation Caburator WEBER
In stock