- Levier de commande d'accélérateur pour UN carburateur WEBER 40DCOE ET 45DCOE
- Adaptable sur R8 et Alpine A110 avec pipe pour un carburateur WEBER
- Dimension du centre de l'arbre au centre de la rotule: 23,50 mm
- Rotule Ø 8mm
In stock
Throttle control adjustment screw for WEBER 40 DCOE and 45 DCOE carburetor
Reference:
48068
- Suitable for WEBER 40DCOE and 45DCOE carburetors
- M5x32 screw
- Head width 8mm
- Number 52 on exploded view
- Compatible with other WEBER carburetors, see below
€3.90
(tax incl.)
Order before 1pm and enjoy same day shipping !
Below are the various WEBER carburetors compatible with part number AVP48068:
|
Carburetor Inlet Diameter |
Carburetor Type or Model |
|---|---|
| from Ø22 to Ø45 |
22 IM, 26/34 DHSA, 26 IMB, 26 IM, 28/36 DHSA, 28/36 DCD, 28/36 DCB, 30 DGS, 30 DGF, 32 DFE-DFM, 32/36 DFV, 32 IMPE, 32 ICS, 32 ICR, 32 ICB, 32 DMSA, 32 DIR, 32 DIF, 32 DHSA, 32 DHS, 32 DFD, 32 DFB, 32 DCOF, 34 ICT, 34 DMS, 34 DHS, 34 DCS, 34 DCHD, 34 DCHE, 35 DCNL, 36 DCNF, 36 DCNFA, 36 DCD,38 DCOE, 38 DCNL,40 DCOE,42 DCOE, 45 DCOE. |
You may also like
- Throttle control lever for TWO WEBER 40DCOE AND WEBER 45DCOE carburetors
- Allows carburetor synchronization
- Suitable for R8 Gordini, Alpine A110, Simca Rallye
- 8mm diameter ball joint
In stock
- Idle speed adjustment screw spring for WEBER 40DCOE and 45DCOE
- sold individually, ,eed 2 pieces for one carburettor
- Part number 47 on the exploded view
- Fits other WEBER carburettors, see below
In stock
Customers who bought this product also bought:
- Suitable for WEBER 40DCOE carburetor
- Extension length from the carburetor = 25mm
- Stud/nut mounting
- Allows the installation of high-performance filters REF 48099 or 48100
- Also suitable for AVP stock filter ref 48103
- If installing with the new-generation venturi REF 48084 or REF 48085, the installation of the spacer REF 48087 is recommended.
- For competition use
In stock
In stock
In stock
- Intake manifold mounting distance: 70mm and 110mm
- Carburetor mounting distance: 110mm and 70mm
- Flange thickness: 19.3mm
- Pipes diameter: Ø 45mm
- Flanges supplied with O-rings (x4), paper gaskets (x4), and mounting studs (x16)
These rigid aluminum flanges replace the original "flexible" rubber flanges, which tear with wear.
In stock
- Suitable for WEBER 40DCOE and 45DCOE carburetors,
- For 23g or 26g brass or plastic float,
- Requires 1 piece per carburetor,
- Number 72 on the exploded view,
- Also suitable for the following carburetors: DCOE, DCO/SP, 40DCZ, IDF, 28/36 DCB, 28/36 DCD, 28/36 DCLD, 34 DCHD, 34 DCS, 36 DCD, 36 DCLD.
In stock
- Kit of 4 springs for locking the venturi in the body of the WEBER DCOE 40 and DCOE 45 carburetor
- For first generation Caburator WEBER
In stock
- Suitable for WEBER 40DCOE AND 45DCOE carburetors
- This fits on the side opposite the throttle control
- Part number 86 on exploded view
- Also suitable for: 30 IBA, 32 IBA, 36 DCNF, 36 DCNFA, 36 DCNV, 36 DCNVA, 38 DCOE, 40 DCOE, 42 DCOE, 45 DCOE, 48 DCO/SP, 48 IDA.
In stock
- Suitable for older generation WEBER 40DCOE carburetors (the bearing surfaces differ from the shafts of modern versions)
- Caution: Mounting must be done with flat-head screws (AVP48052)
- Drilling required for accelerator pump control
- Overall shaft length: 180mm
- Part number 85 on the exploded view
In stock