- For M12 banjo bolts
- Number 70 on exploded view
In stock
Gasket under banjo screw head or filter cap Weber 40 / 45 DCOE carburetor
Reference:
48032
- Gasket dimensions: Ø 20x12x1mm
- Suitable for WEBER 40DCOE and 45DCOE carburetors
- Number 2 and number 69 on exploded view
- Sold individually, 1 piece required for one carburetor
- Compatible with other WEBER carburetors, see below
€1.80
(tax incl.)
Order before 1pm and enjoy same day shipping !
Below are the various WEBER carburetors compatible with the AVP48032 reference:
|
Carburetor Inlet Diameter |
Type or model of Carburetor |
|---|---|
| from Ø22 to Ø28 |
22 IM, 26 IM, 26 IMB, 26 OC, 28 IMB, 28 ICP, 28/36 DCB, 28/36 DCD, 28/30 DFTH |
| from Ø30 to Ø38 |
30 ICF, 32 DCOF, 32 ICS, 32 IMPE, 34 DCHD, 34 DCHE, 34 DCS, 36 DCA, 36 DCD, 36 DCNF, 36 DCNFA, 36 DCNV, 36 DCNVA, 36 DCNVH, 36 IDF, 38 DCOE |
|
from Ø40 to Ø50 |
40 IDF, 40 DCOE, 42 DCNF, 42 DCOE, 44 DCNF, 44 IDF, 45 DCOE, 48 DCOE, 48 IDA,48 IDF, 48 DCO/SP, 50 DCO/SP, 55 DCO/SP |
You may also like
- For M12 banjo bolts
- Number 98 on exploded view
In stock
- M12 Banjo Bolt
- Sold individually without gasket
- Number 70 on exploded view
In stock
- Banjo screw M12
- Sold individually without gasket
In stock
- Suitable for WEBER 40DCOE 151 and 45DCOE 152 (latest generation)
-
Sold individually, need 2 pieces for one carburettor
- Number 56 on exploded view
- Compatible with other WEBER carburettors, see below
In stock
- Suitable for WEBER 40DCOE and WEBER 45DCOE carburettor
- Thread16x1.5
- Need 1 piece for a carburetor
- Number 1 on exploded view
- Compatible with other WEBER carburetors, see below
In stock
- Suitable for WEBER 40DCOE and 45DCOE carburetors
- Requires 1 part per carburetor
- Number 3 on exploded view
- Compatible with other WEBER carburetors, see below
In stock
Customers who bought this product also bought:
- Suitable for WEBER DCOE 40 and DCOE 45 carburetors
- Free spring length: 59mm
- Wire diameter: Ø 0.4mm
- Original Weber part number: 47600.064
- Number 60 on the exploded view
In stock
- This kit contains an M9 adjustment screw nut and an M8 nut.
- Kit sold with a strong Ø 38mm square gasket and a weak Ø 38mm gasket.
- The supply of these two seals allows you to install the most suitable seal depending on the wear of the caliper grooves.
- To identify a caliper with a square or round seal, refer to the symbol indicated on the caliper casting.
- A square symbol indicates a square seal, while a circle symbol indicates a round seal.
- It is essential to replace the same type of seal (round or square) according to the symbol on the caliper.
- We recommend checking the symbol displayed on each caliper, as a vehicle may have Calipers of different origins, some of which may have square joints and others round joints.
- It is not recommended to mix calipers on the same set, as this can lead to the risk of skewing during braking.
In stock
In stock
Compatible for any Ducellier igniter with an inside diameter of the body of 58.8mm
In stock
- Shifting washer against throttle shaft bearing for carburettor WEBER 40DCOE AND WEBER 45DCOE
- Thickness: 0.5mm
- Inner Ø: 7mm
- Outer Ø: 14mm
- Number 77 on exploded view
In stock
- Sheet Dimensions: Length 58cm x Width 35cm
- Sheet Thickness: 0.8mm
- Ideal for making carburetor gaskets, fuel pump gaskets, engine and gearbox gaskets (Parts subject to low temperature or pressure). Suitable for all other types of flat gaskets, except those in contact with vapors, up to a temperature limit of 120°C.
- Material made of fiber paper
In stock
In stock