In stock
Carburetor & Carburetor Parts R17 / R17G
Carburetion & Fuel System – Renault R17 & R17 Gordini
For your Renault R17 or R17 Gordini, we offer a complete selection of engine fuel system parts, compatible with Cléon cast iron engines and specific Gordini configurations.
AVP spare parts available for your R17 carburetion system:
- Weber single or dual-barrel carburetors for original equipment or retrofitting
- Fuel pumps, mechanical or electric depending on the year and version
- Accelerator pump diaphragms, injectors, needles, jets, floats
- Carburetor gaskets, shrouds, pipes, and aluminum flanges
- R17-specific throttle controls and levers
- Fuel lines, fittings, clamps, copper tubes
- High-efficiency fuel filters to protect the system
- Anti-corrosion tank treatments to preserve the entire system
Whether you're restoring an R17 TL, TS, or a Gordini version, AVP – Arnaud Ventoux Pièces can help you offers reliable, workshop-tested components with in-stock availability and fast shipping.
Mounting center distance (Width): 48.5mm
Mounting center distance (Length): 92mm
Thickness: 5mm
In stock
In stock
Stem length: 38mm
Center distance of the membrane holes 27mm
In stock
In stock
In stock
Inlet diameter: 61mm
Dimension of the fitting on the carburettor: Length 115mm x Length 70mm
Out of stock
In stock
In stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
M5X22 screws
Sold individually, requires 9 pieces for one carburetor
Number 5 on exploded view
Compatible with other WEBER carburetors, see below
In stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors,For 23g or 26g brass or plastic float,Requires 1 piece per carburetor,Number 72 on the exploded view,Also suitable for the following carburetors: DCOE, DCO/SP, 40DCZ,...
In stock
In some configurations, Weber DCOE carburetors are positioned directly above the exhaust, which can create vapor lock problems due to heat: our AVP48010 plate can solve this problem
Plate can be covered with thermal...
In stock
For M12 banjo bolts
Number 70 on exploded view
In stock
For M12 banjo bolts
Number 98 on exploded view
In stock
M12 Banjo Bolt
Sold individually without gasket
Number 70 on exploded view
In stock
Banjo screw M12
Sold individually without gasket
In stock
Gasket dimensions: Ø 20x12x1mm
Suitable for WEBER 40DCOE and 45DCOE carburetors
Number 2 and number 69 on exploded view
Sold individually, 1 piece required for one carburetor
Compatible with other WEBER carburetors,...
Out of stock
Joint dimensions: Ø 20x16x1mm
In stock
The kit consists of:
"T" fuel connector x1
90° elbow fuel connector x1
Banjo connector screw x2
Banjo screw under head seal x2
Banjo screw lower seal x2
Hose clamp: Size 12-14mm x3
In stock
The kit consists of:
90° elbow fuel connector x1
Banjo connector screw x1
Banjo screw under head gasket x1
Banjo screw lower gasket x1
Hose clamp: Size 12-14mm x1
In stock
Sold individually, 1 required per carburetor,
Number 4 on exploded view
In stock
In stock
Suitable for WEBER 40DCOE and WEBER 45DCOE carburettor
Thread16x1.5
Need 1 piece for a carburetor
Number 1 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Requires 1 part per carburetor
Number 3 on exploded view
Compatible with other WEBER carburetors, see below
In stock
In stock
In stock
In stock
Need 3 AVP6815 gaskets and 1 AVP6816 gasket to equip one engine
In stock
Need 1 AVP6816 gasket and 3 AVP6815 gaskets to equip an engine
In stock
Ideal assembly with a pair of aluminium flanges Ref: AVP6810
Out of stock
Delivered with these O-rings (x4) and these paper seals (x4)
In stock
In stock
In stock
Flanges with tapping for a vacuum
Flanges to be assembled directly on the carburetors, the seal is ensured by O-rings (delivered with 4 O-rings)
In stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
External mounting
Fixes to the carburetor cover
In stock
In stock
In stock
In stock
In stock
Levier de commande d'accélérateur pour UN carburateur WEBER 40DCOE ET 45DCOE
Adaptable sur R8 et Alpine A110 avec pipe pour un carburateur WEBER
Dimension du centre de l'arbre au centre de la rotule: 23,50 mm
Rotule...
In stock
Throttle control lever for TWO WEBER 40DCOE AND WEBER 45DCOE carburetors
Allows carburetor synchronization
Suitable for R8 Gordini, Alpine A110, Simca Rallye
8mm diameter ball joint
Out of stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
M5x32 screw
Head width 8mm
Number 52 on exploded view
Compatible with other WEBER carburetors, see below
In stock
In stock
In stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Number 83 on exploded view
In stock
Lower bowl cover gasket ref 48110 for WEBER 40DCOE and 45DCOE
Number 36 on exploded view
In stock
Installation possible on all AVP horns
Length 115mm (can be cut to size)
Clamp included
Sold in pairs
In stock
In stock
Suitable for WEBER 45DCOE carburetor
Extension length from the carburetor = 48mm
Stud/nut mounting
Allows installation of AVP high-performance filter part number 48101 or 48102
Also suitable for AVP sock filter part...
Out of stock
Aluminum air intake horn/trumpet for WEBER 45DCOE carburetor
48mm extension over the carburetor
Stud/nut mounting
Allows installation of high-performance filter REF 48101 or 48102
Also suitable for AVP sock filter...
In stock
Air intake horn/trumpet for WEBER 45DCOE carburetor,
Extension length from the carburetor: 62mm,
ATTENTION: Must be installed with venturi REF 48086,
Fixing with kit REF 48098,
Suitable for mounting AVP filters REF...
In stock
Allows to clamp the horns on the body of the WEBER 45DCOE carburetor
ATTENTION: essential for REF 48096 horns.
Kit for a carburetor consisting of 4 stop tabs, 4 washers and 4 nuts
Also suitable for WEBER 48DCOE...
In stock
Air intake trumpet filter for WEBER 45DCOE carburetor
Fitment possible on all AVP trumpets
Mesh filters that feature two layers of stainless steel mesh with a filter layer in between to ensure maximum engine...
In stock
Suitable for Weber DCOE 45 carburetor air intake horn/trumpet
Fixed with a screw collar on a rubber flange for a perfect seal
Can be fitted to all AVP DCOE45 air intake horns/trumpets
Overall length: 115mm
Diameter:...
In stock
In stock
In stock
Suitable for WEBER 45DCOE carburetor with needle screw locking
Allows the installation of 62mm air intakes/trumpets REF 48096
Installation possible on older-generation carburetors with spring-locked venturis provided...
In stock
Kit of 4 springs for locking the venturi in the body of the WEBER DCOE 40 and DCOE 45 carburetor
For first generation Caburator WEBER
In stock
Brake for venturi locking screw for carburettor WEBER 40DCOE and 45DCOE latest generation
Number 24 on exploded view
In stock
WARNING: Suitable for Venturi ref 48085 and ref 48086 for WEBER 40DCOE and 45DCOE carburetors.
Allows you to stop the movement of the venturi for older generation DCOEs, and stop the movement of the nozzle and...
In stock
In stock
Suitable for all types of WEBER 45 DCOE carburetors
Suitable for 1600cc original or similar carburetors
In stock
Suitable for all types of WEBER 45DCOE carburetors
Suitable for 1600cc big valves or similar
In stock
Suitable for all types of WEBER 45DCOE carburetors
Suitable for 1800cc Gr4 or similar
Out of stock
Suitable for first generation WEBER 40DCOE and 45DCOE carburetors
Sold individually, requires 2 pieces for one carburetor
Number 56 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Suitable for WEBER 40DCOE 151 and 45DCOE 152 (latest generation)
Sold individually, need 2 pieces for one carburettor
Number 56 on exploded view
Compatible with other WEBER carburettors, see below
In stock
Suitable for WEBER 40DCOE and 45DCOE
sold individually, need 2 pieces for one carburettor
Part number 46 on exploded view
Compatible with other WEBER carburettors, see below
Out of stock
Suitable for carburettor WEBER 40DCOE / 45DCOE
To ensure a perfect seal between the mixture screw and the carburettor body (do not forget the support cup)
sold individually, need 2 pieces for a carburettor
Number...
In stock