In stock
Carburetor & Carburetor Parts Matra Djet
Carburetors & Parts for Matra Djet
Find our selection of carburetors and spare parts specifically designed for the maintenance, repair, or restoration of Matra Djets.
Spare parts available for Matra Djet carburetors:
- Complete carburetors: Weber 40 DCOE, Solex 35 PHH depending on the version
- Main, idle, air, and pump jets
- Needle valves, floats, accelerator pump pistons
- Mixture screws, springs, shafts, and parts Tuning
- Carburetor gaskets individually or in complete sets
- Aluminum flanges and intake manifolds
- Throttle controls, levers, and mounting accessories
- Specific tools for float adjustment or calibration
Whether you opt for a original restoration or a light preparation, at AVP you will find the necessary components for a high-performance, well-tuned carburetor.
In stock
In stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
M5X22 screws
Sold individually, requires 9 pieces for one carburetor
Number 5 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Number 83 on exploded view
In stock
Lower bowl cover gasket AVP48118
Number 36 on exploded view
In stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors,For 23g or 26g brass or plastic float,Requires 1 piece per carburetor,Number 72 on the exploded view,Also suitable for the following carburetors: DCOE, DCO/SP, 40DCZ,...
In stock
In some configurations, Weber DCOE carburetors are positioned directly above the exhaust, which can create vapor lock problems due to heat: our AVP48010 plate can solve this problem
Plate can be covered with thermal...
In stock
For M12 banjo bolts
Number 70 on exploded view
In stock
For M12 banjo bolts
Number 98 on exploded view
In stock
M12 Banjo Bolt
Sold individually without gasket
Number 70 on exploded view
In stock
Banjo screw M12
Sold individually without gasket
In stock
Gasket dimensions: Ø 20x12x1mm
Suitable for WEBER 40DCOE and 45DCOE carburetors
Number 2 and number 69 on exploded view
Sold individually, 1 piece required for one carburetor
Compatible with other WEBER carburetors,...
In stock
Joint dimensions: Ø 20x16x1mm
In stock
The kit consists of:
"T" fuel connector x1
90° elbow fuel connector x1
Banjo connector screw x2
Banjo screw under head seal x2
Banjo screw lower seal x2
Hose clamp: Size 12-14mm x3
In stock
The kit consists of:
90° elbow fuel connector x1
Banjo connector screw x1
Banjo screw under head gasket x1
Banjo screw lower gasket x1
Hose clamp: Size 12-14mm x1
In stock
Sold individually, 1 cover required per carburetor
Number 4 on exploded view
In stock
In stock
Suitable for WEBER 40DCOE and WEBER 45DCOE carburettor
Thread16x1.5
Need 1 piece for a carburetor
Number 1 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Requires 1 part per carburetor
Number 3 on exploded view
Compatible with other WEBER carburetors, see below
In stock
In stock
In stock
In stock
In stock
In stock
Intake manifold mounting distance: 70mm and 110mm
Carburetor mounting distance: 110mm and 70mm
Flange thickness: 19.3mm
Pipes diameter: Ø 40mm
Flanges supplied with O-rings (x4), paper gaskets (x4), and mounting...
In stock
In stock
In stock
Carburetor mounting distance to the intake manifold: 110mm and 70mm
Manifold supplied with O-rings (x2) and studs (x4) for mounting the carburetor
The carburetor is mounted directly onto the manifold. The seal is...
In stock
In stock
In stock
Out of stock
In stock
In stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
External mounting
Fixes to the carburetor cover
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
M5x32 screw
Head width 8mm
Number 52 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Throttle control lever for TWO WEBER 40DCOE AND WEBER 45DCOE carburetors
Allows carburetor synchronization
Suitable for R8 Gordini, Alpine A110, Simca Rallye
8mm diameter ball joint
In stock
Levier de commande d'accélérateur pour UN carburateur WEBER 40DCOE ET 45DCOE
Adaptable sur R8 et Alpine A110 avec pipe pour un carburateur WEBER
Dimension du centre de l'arbre au centre de la rotule: 23,50 mm
Rotule...
In stock
Suitable for WEBER 40DCOE carburetor
Extension length from the carburetor = 25mm
Stud/nut mounting
Allows the installation of high-performance filters REF 48099 or 48100
Also suitable for AVP stock filter ref 48103...
In stock
Aluminum air intake horn/trumpet for WEBER 40DCOE carburetor
43mm extension over the carburetor
Stud/nut mounting
Allows installation of high-performance filter REF 48099 or 48100
Also suitable for AVP sock filter...
In stock
Air intake horn/trumpet for WEBER 40DCOE carburetor
Extension length from the carburetor: 55mm
ATTENTION: Must be fitted with venturi REF 48084 or 48085
Fixing with kit REF 48097
Suitable for fitting AVP filters ref...
In stock
Air intake horn/trumpet for WEBER 40DCOE carburetor
Extension length from the carburetor: 75mm
ATTENTION: Must be installed with venturi REF AVP 48084 or 48085
Fix with kit REF 48097
Suitable for mounting AVP filters...
In stock
Allows to clamp the horns on the body of the WEBER 40DCOE carburetor
ATTENTION: essential for REF 48093 horns
Kit for a carburetor consisting of 4 stop tabs, 4 washers and 4 nuts
Also suitable for WEBER 42DCOE...
In stock
Air intake horn/trumpet filters for WEBER 40DCOE carburetor
Fitment possible on all AVP air intake horns
Mesh filters that feature two layers of stainless steel mesh with a filter layer in between to ensure maximum...
In stock
Suitable for Cornet/Air intake trumpet of the Weber DCOE 40 carburetor,
Fixing by screw necklace on rubber flange for perfect sealing,
Possible assembly on all AVP cornets for DCOE40,
Overall length: 115mm,
Diameter:...
In stock
In stock
In stock
Installation possible on all AVP horns
Length 115mm (can be cut to size)
Clamp included
Sold in pairs
In stock
In stock
Suitable for WEBER 45DCOE carburetor
Extension length from the carburetor = 48mm
Stud/nut mounting
Allows installation of AVP high-performance filter part number 48101 or 48102
Also suitable for AVP sock filter part...
In stock
Aluminum air intake horn/trumpet for WEBER 45DCOE carburetor
48mm extension over the carburetor
Stud/nut mounting
Allows installation of high-performance filter REF 48101 or 48102
Also suitable for AVP sock filter...
In stock
Air intake horn/trumpet for WEBER 45DCOE carburetor,
Extension length from the carburetor: 62mm,
ATTENTION: Must be installed with venturi REF 48086,
Fixing with kit REF 48098,
Suitable for mounting AVP filters REF...
In stock
Allows to clamp the horns on the body of the WEBER 45DCOE carburetor
ATTENTION: essential for REF 48096 horns.
Kit for a carburetor consisting of 4 stop tabs, 4 washers and 4 nuts
Also suitable for WEBER 48DCOE...
In stock
Suitable for Weber DCOE 45 carburetor air intake horn/trumpet
Fixed with a screw collar on a rubber flange for a perfect seal
Can be fitted to all AVP DCOE45 air intake horns/trumpets
Overall length: 115mm
Diameter:...
In stock
Suitable for WEBER 40DCOE carburetors with spring lock,
Suitable for first-generation WEBER 40DCOEs with 55mm air intake nozzle REF 48093,
WARNING: If you are not using the 55mm air intake nozzle REF 48093, you must...
In stock
Suitable for Latest generation WEBER 40DCOE carburetor with 55mm air intake nozzle REF 48093
WARNING: If you are not using the 55mm air intake nozzle REF 4093, you must use the spacer REF 48087 to fill the gap...
In stock
Kit of 4 springs for locking the venturi in the body of the WEBER DCOE 40 and DCOE 45 carburetor
For first generation Caburator WEBER
In stock
Suitable for WEBER 45DCOE carburetor with needle screw locking
Allows the installation of 62mm air intakes/trumpets REF 48096
Installation possible on older-generation carburetors with spring-locked venturis provided...
In stock
WARNING: Suitable for Venturi ref 48085 and ref 48086 for WEBER 40DCOE and 45DCOE carburetors.
Allows you to stop the movement of the venturi for older generation DCOEs, and stop the movement of the nozzle and...
In stock
Brake for venturi locking screw for carburettor WEBER 40DCOE and 45DCOE latest generation
Number 24 on exploded view
In stock
Suitable for all types of WEBER 40DCOE carburetors
In stock
Suitable for all types of WEBER 40DCOE carburetors
In stock
Suitable for all types of WEBER 40DCOE carburetors
In stock
Suitable for all types of WEBER 45 DCOE carburetors
Suitable for 1600cc original or similar carburetors
In stock
Suitable for all types of WEBER 45DCOE carburetors
Suitable for 1600cc big valves or similar
In stock
Suitable for all types of WEBER 45DCOE carburetors
Suitable for 1800cc Gr4 or similar
In stock
Suitable for WEBER 40DCOE 151 and 45DCOE 152 (latest generation)
Sold individually, need 2 pieces for one carburettor
Number 56 on exploded view
Compatible with other WEBER carburettors, see below
In stock
Suitable for first generation WEBER 40DCOE and 45DCOE carburetors
Sold individually, requires 2 pieces for one carburetor
Number 56 on exploded view
Compatible with other WEBER carburetors, see below
In stock