Steering wheel covered in high-quality black leather with white stitching and parallel patterns
Steering wheel entirely handmade
Steering wheel outer diameter: Ø 350mm
Dotting: 39mm
Steering wheel cross-section:...
In stock
Performance & Racing Parts Simca Rallye 2 / Rallye 3
Our performance and Racing spare parts for your Simca Rallye 2 / Simca Rallye 3
Discover here a wide selection of parts and accessories designed to improve and boost the performance of your Simca Rallye 2 / Simca Rallye 3
Whether you are looking for electronic ignition, iridium spark plugs, rear tie rods, a sports-prepared camshaft, oil pan, exhaust manifold, sports silencer, steering rod, manual choke, circuit breaker...at AVP, Arnaud Ventoux Pièces, you will find everything you need to optimize the operation of your old one with quality components.
Steering wheel covered in aged black leather for an authentic, vintage look with white stitching and parallel patterns
Steering wheel entirely handmade
Steering wheel outer diameter: Ø 350mm
Thickness: 39mm
Steering...
In stock
Steering wheel covered in high-quality black leather, white stitching with parallel patterns
Steering wheel entirely handmade
Steering wheel outer diameter: Ø350mm
Dotting: 39mm
Steering wheel cross-section: 30mm
Hub...
In stock
Out of stock
In stock
Mechanism to be mounted only with disc reference 9104
Out of stock
In stock
Supplied with 4 carburetor mounting studs
Carburetor mounting stud distance: 110mm and 70mm
The carburetor is mounted directly onto the manifold. A seal is ensured by two paper gaskets; there is no need to use...
In stock
Supplied with x8 mounting studs and x4 O-rings (AVP4806) between the manifold and the carburetor.
Carburetor mounting stud distance: 110mm and 70mm
The carburetors are mounted directly onto the manifold. A...
In stock
Intake ducts: Ø 33mm
In stock
Center distance between flange and intake manifold (Side without stud): 32mm and 102mm
Center distance between flange and carburetor (Side with stud): 92mm and 60mm
Flange thickness: 17.5mm
Pipes diameter: Ø 36.5mm...
In stock
In stock
In stock
Intake manifold mounting distance: 70mm and 110mm
Carburetor mounting distance: 110mm and 70mm
Flange thickness: 19.3mm
Pipes diameter: Ø 40mm
Flanges supplied with O-rings (x4), paper gaskets (x4), and mounting...
In stock
In stock
In stock
Intake manifold mounting distance: 70mm and 110mm
Carburetor mounting distance: 110mm and 70mm
Flange thickness: 19.3mm
Pipes diameter: Ø 45mm
Flanges supplied with O-rings (x4), paper gaskets (x4), and mounting...
In stock
In stock
In stock
Stainless steel airbox: high corrosion resistance and durability
In stock
45mm Clip for Stainless Steel Airbox
Material: Stainless Steel
Sold individually
Suitable for:
Weber 40 DCOE carburetor
Weber 40 DCOM carburetor
In stock
In stock
Stainless steel airbox: high corrosion resistance and durability
In stock
65mm Clip for Stainless Steel Air Box
Material: Stainless Steel
Sold individually
Suitable for:
Weber 45 DCOE Carburetor
Weber 45 DCOM Carburetor
In stock
In stock
Ideal for prepared engines or to replace a mechanical fuel pump.
Flow rate: 125l/h
Max pressure: 0.30bar
Suction: -0.10bar
220° adjustable inlet and outlet tube: Ø 8mm
Self-regulated fuel pump
Dimensions: 73x126mm /...
In stock
In stock
FACET Silver Top 113 l/h Fuel Pump (476087) self-regulating with integrated fuel filter
These pumps reduce the "Vapor Lock" effect by allowing for a more consistent fuel supply.
They must be mounted in a vertical...
In stock
FACET Silver Top 113 l/h Fuel Pump (476087) self-regulating with integrated fuel filter
These pumps reduce the "Vapor Lock" effect by allowing for a more consistent fuel supply.
They must be mounted in a vertical...
In stock
Fitting Specifications:
Inlet Thread Diameter: 1/8 x 27 NPTF
Outlet Diameter: Ø 8mm
Orientation: 90° Elbow
Material: Brass
Sold individually
Suitable for Facet fuel pumps of the following types: Silver Top / Red Top...
Out of stock
Fitting Specifications:
Inlet Thread Diameter: 1/8 x 27 NPTF
Outlet Diameter: Ø 8mm
Orientation: Right
Material: Brass
Sold individually
Suitable for Facet fuel pumps of the following types: Silver Top / Red Top and...
In stock
Fuel filter with 74-micron filtration
Filter diameter: 40mm
Filter height: 35mm
Suitable for Facet fuel pumps of the following types: Silver Top / Red Top and Gold-Flo
In stock
Seal Diameter: Ø 24x51 mm
Seal Thickness: 3 mm
Material: Specific hydrocarbon rubber
Suitable for Facet fuel pumps of the following types: Silver Top / Red Top and Gold-Flo
Seal must be replaced each time the pump...
In stock
This silent block kit is used for mounting Facet pumps and allows the pump to be fixed to the body, preventing vibrations.
Suitable for Facet fuel pumps of the following types: Silver Top / Red Top and Gold-Flo
Kit...
In stock
Glass bowl Ø 67mm
Filter element: Interchangeable paper cartridge
One inlet: dual size 6 and 8mm
One outlet: dual size 6 and 8mm
Regulation pressure: Regulation range from 0 to 0.6 bar
Compatible with fuel SP95 /...
In stock
Glass jar Ø 67mm
Filter element: Replaceable paper cartridge
One Inlet: dual size 6 and 8mm
One Outlet: dual size 6 and 8mm
Regulating pressure: Regulating range from 0 to 0.6 bar
Compatible with SP95 / SP98 / E85...
In stock
These iridium-electrode spark plugs are suitable for both daily road use and rallying. They are designed to improve engine reliability and performance, whether hot or cold.
Suitable for:
A110.1600 (S / SC / SI)
R12G...
In stock
Kit to be used with a coil of primary resistance between 2.5 and 3.5 ohms
Compatible with coils AVP4708 and AVP4715
Compatible for Ducellier igniter with an inner body diameter of Ø 58.8mm
Not suitable for an igniter...
In stock
Kit to be used with a coil of primary resistance between 2.5 and 3.5 ohms
Compatible with coils AVP4708 and AVP4715
Compatible for Ducellier igniter with an internal body diameter of Ø 58.8mm
Not suitable for an...
In stock
Out of stock
To be fitted with manifold AVP9053
In stock
Exhaust heat wrap reduces heat radiation from manifolds, silencers, or full exhaust systems when wrapped directly around the pipes. It effectively protects the engine bay and heat-sensitive components (starter motor,...
In stock
Exhaust heat wrap reduces heat radiation from manifolds, silencers, or full exhaust systems when wrapped directly around the pipes. It effectively protects the engine bay and heat-sensitive components (starter motor,...
In stock
Flexor Specifications:
Mounting hole spacing:4 x 50.50 mm
Mounting hole diameter: Ø 8.4 mm
Center hole diameter:Ø 10.50 mm
Flexor thickness: 11 mm
Material:Rubber flexor with metal reinforcement
Supplied with 4 x...
In stock
In stock
Steering Ball Joint for Adjustable Tie Rods - M12x100 (Left Hand Thread) - All Models (1970 Onwards)
1000/R1/R2/R3/Coupe 1000/1200S/CG
In stock
In stock
In stock
In stock
In stock
Adjustable shock absorber stiffness.
Versatile "Road" shock absorbers, ideal for road use and competition.
Detailed description of Koni shock absorbers, see below
In stock
These twin-tube hydraulic adjustable shock absorbers are designed for versatile use, such as sporty driving.
With an adjustable damping range from softest to firmest,they are perfect for performance driving, sporty...
In stock
Adjustable shock absorber stiffness.
Versatile "Road" shock absorbers, ideal for road use and competition.
Detailed description of Koni shock absorbers, see below
In stock
These twin-tube hydraulic adjustable shock absorbers are designed for versatile use, such as sporty driving.
With an adjustable damping range from softest to firmest,they are perfect for performance driving, sporty...
In stock
Kit of 6 stainless steel braided brake hoses—stronger and more durable than the original rubber ones—for firmer, more precise braking.
These hoses are direct replacements for the original hoses.
Kit contents:
Front...
In stock
Use reserved for competition, do not use these pads on public roads.
In stock
Suitable for the following vehicles:
Rallye 2: 1976-1977: Rear Brakes
Rallye 3: 1978: Rear Brakes
Brake Pad Dimensions:
Width: 109mm
Height: 39mm
Thickness: 10mm
For competition use only. Do not use these brake...
In stock
Overall length: 271cm
Sheath length: 87cm
Cable length: 268cm
Our cables are made in France and meet the assembly and quality standards of original equipment (OEM) cables from automotive manufacturers.
In stock
Overall length: 271 cm
Cable length: 271 cm
CableØ 2 mm
Sold without sheath, compatible with original cable sheaths
Our cables are made in France and meet the assembly and quality standards of original equipment...
In stock
Vintage round long-range driving light, "Oscar" type (Ø 180mm)
Light unit specifications:
Housing diameter: Ø 181mm
Lens diameter: Ø 145mm
Overall height: 204mm
Depth: 125mm
Mounting base: M12 - Adjustable (Up/Down)...
In stock
Out of stock
In stock
