This deflector is suitable for all wiper arms with flat arms 7mm wide and 2.5mm thick (After 1970)
This accessory allows for better support of the blades on the windshield while driving, and provides a beautiful...
In stock
Best sellers
Adaptable leather gear knob with visible stitching
Knob dimensions:
Knob diameter: Ø 47.5 mm
Knob height: 60 mm
Supplied with 3 different tips to fit all types of levers (screwed or glued):
Chrome screw-on tip:...
In stock
Built-in short extensions
Straight coil terminal
Coil wire length: 50cm
This ignition harness consists of 4 spark plug wires and one coil wire.
We would like to point out that our spark plug harnesses are...
In stock
In stock
Crimp Diameter: Ø 70.9mm
Thickness: 1.45mm (Original dimension)
Material: Multi-layer with steel crimp
In stock
Filter Dimensions:
Length (D1): 271mm
Width (D3): 134mm
Height (H1): 42mm
The dimensions given are for information purposes only; slight variations of a few millimeters are possible depending on availability.
In stock
Filter Dimensions:
Inner Diameter (D2): Ø 124mm
Outer Diameter (D1): Ø 173mm
Height (H1): 41mm
The dimensions given are for guidance only; slight variations of a few millimeters are possible depending on availability.
In stock
In stock
Original chassis mounting with 4 screws (See photo of mounting center distance)
Suitable for gear knob with M12 thread
Gear lever height from chassis mounting: 27cm
Aluminum base with reinforced, maintenance-free...
In stock
Allows easy adjustment of the float with one side of the tool calibrated to 8mm and the other side to 9mm.
Allows direct action on the float tab thanks to a slot at the end of the tool.
In stock
Suitable for all types of WEBER 45DCOE carburetors
Suitable for 1600cc big valve engines or similar
In stock
Air intake trumpet/trumpet for WEBER 40DCOE carburetor
Protrusion length from the carburetor: 55mm
ATTENTION: Must be mounted with venturi REF 48084 or 48085,
Mounting kit REF 48097,
Suitable for mounting AVP filters...
In stock
Air bypass screw cover for carburettor WEBER 40DCOE and 45DCOE latest generation
Number 25 on exploded view
Also suitable for the following carburettors: 36 DCNF 36 DCNFA 40 / 45 DCOE 40 IT
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
M5x32 screw
Head width 8mm
Number 52 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Suitable for older generation WEBER 40DCOE carburetors (the bearing surfaces differ from the shafts of modern versions)
Caution: The throttle plates or flaps must be mounted using flat-head screws. (AVP48052)
The...
In stock
Choke filter for WEBER 40DCOE and 45DCOE carburetors
Requires 1 piece per carburetor
Part number 87 on exploded view
Also suitable for: 35 DCNL, 36 DCNF, 36 DCNFA, 38 DCNL, 40 DCNF, 40 DCNL, 38 DCOE, 40 DCOE, 42...
In stock
In stock
For reliability reasons, it is advisable to keep the original pinion of the distributor
Note included for installation of the pinion on the new distributor
It is advisable to mount these electronic distributors with...
In stock
Sheets (x4)
Sheet Dimensions:
Sheet Bore Diameter: Ø 75.7mm
Sheet Flange or Top Diameter (D): Ø 89.75mm
Sheet Base Diameter (A): Ø 80mm
Sheet Height (including skirts, overall) (C): 128mm
Sheet Height to Base...
In stock
In stock
Out of stock
Limited special offer
In stock
Diamond Dimensions:
Height: 37mm
Width: 26mm
One mounting stud: Ø 4mm
In stock
Segment Characteristics:
Segment Diameter: Ø 74.50mm
Thickness of Upper Segments (Fire-resistant): 1.50mm
Thickness of Intermediate Segments (Waterproof): 2mm
Low ring thickness (Scraper):4mm
It is essential to...
In stock
In stock
In stock
Limited special offer
In stock
To be fitted with manifold AVP9053
In stock
In stock
Triangle sold with its silentblocs (x4)
Suitable for:
A310 V6 (Phase 2): From chassis 47709 to the end of series(From 1981)
R5 Turbo 1 and 2 (8220)
Out of stock
Dimension of the axis of the upper fixing bolt at the support of the 1st washer 14cm
In stock
In stock
In stock
In stock
Out of stock
Handbrake cable with chassis mounting
Overall length: 202 cm
Sheath length: 28 cm
Cable length: 200,5 cm
Our cables are made in France and meet the assembly and quality standards of original equipment (OEM)...
Out of stock
Crankcase supplied complete with mounting studs (x12 M6 screws / 70 mm length), washers, nuts, and drain plug.
Aluminum crankcase.
In stock
In stock
Radiator Dimensions:
Radiator Inlet Diameter: Ø 18mm
Radiator Outlet Diameter: Ø 8.1mm
Radiator Height: 194mm
Radiator Width: 138mm
Radiator Depth/Thickness: 42mm
Material: Aluminum core and plastic housing
Supplied...
In stock
Manual windshield washer pump: adaptable
1 inlet Ø5mm and 1 outlet Ø5mm
With push button
In stock
Engine-specific gasket kit for large bearings: including a crankshaft oil seal (flywheel side) Ø 80x100x13mm and an oil pan gasket (large bearing).
Suitable for:
R12 L / TL / TS : 1289cc engine (Type 810)
R15 TL /...
In stock
Hose inner diameter: Ø 9mm
Sold individually
May need to be cut to size on some fuel-injected versions
Ref OE Renault / Alpine: 0857719300 / 7700560885 + 7700529421 / 7700574299
Suitable for:
R16 TX: 1647cc engine...
In stock
Sold in pairs
3-pin flat base
Dimensions: 47.5 x 82 mm
Ideal for improving vehicle visibility while maintaining a retro look (Yellow)
Due to the wide variety of bulb types used, please check compatibility with...
In stock
Ignition coil for Ducellier distributor
Suitable for the following vehicles:
Alpine A310-V6:Engine 112-730 / Serial number: 1 -> 40350
Coil: 1 input / 2 poles + ballast / resistor
Primary...
In stock
Mounts after the intermediate tube. See photo #2
Renault OE Ref: 7700859523 / 7700657465
Inlet Tube Diameter: Ø 33mm (internal)
Suitable for:
R4 (956cc/1108cc from 09/1983 to 1992)
R4 (1108cc) from 10/1979 to...
In stock
Suitable for the following vehicles:
R4 / 4L: Type R1120: from chassis number 954001: from 10/1968
R4 / 4L: Type R1123: from chassis number 627132: from 07/1968
R4 / 4L: Type R1126: from 1971
R4 / 4L Safari: from...
In stock
Stainless steel dashboard trim panel with patternto stick on
Dimensions
Length (Overall): 54cm
Width: 9.3cm
In stock
Suspension ball joints: M10x125 axle - Cone Ø 10.80mm to Ø 12.50mm
Mounting center distance on the wishbone: 40mm and 46mm
Ball joint mounting diameter: 30.4mm
OE Renault part number: 0981728300 / 0981711500...
In stock
Inner door panels in black leatherette with black stitching mounted on hardboard
Set of 8 trim pieces for the two front doors and two rear doors
Drilled holes for inserting the original mounting clips AVP4974 or...
In stock
Kit Contents:
Caliper/stub mounting screws: x2
Guide stub: x2
Protective boot: x2
Assembly grease x1
For braking systems: TRW or Lucas type
This kit is suitable for mounting a right or left caliper on a caliper yoke...
In stock
Ball Joint Dimensions:
Cone Diameter: Ø 14.2mm
Thread: M12 x 125 (Right-hand thread)
Supplied with mounting hardware: x4 screws
Suitable for:
Renault 25
Alpine GTA: V6 GT (D500) and V6 Turbo (D501 and D502)
Alpine...
In stock
Original part number: 662304
Part number: Ø 55mm
The operation of the vacuum advance is very important on certain vehicles; it adds 5 to 10°
DUCELLIER part number (Original part number 662304) for DUCELLIER...
In stock
Air intake trumpet/trumpet for WEBER 40DCOE carburetor
Protrusion length from the carburetor: 75mm
ATTENTION: Must be mounted with venturi REF AVP 48084 or 48085
Mounting with kit REF 48097
Suitable for mounting AVP...
In stock
Suitable for GOTTI rims with 6mm diameter mounting holes
Kit includes:
45mm bolts x12
Aluminum cleat x12
Nut washer x24 (requires 2 nut washers per bolt)
Nut x12
In stock
Sold individually
Shim height indicated in the photo
The shims allow you to adjust the rack height, which helps limit variations in alignment during suspension movements.
AVP Accuracy: The two shims can be different...
In stock
Sold individually
Shim height indicated in the photo
The shims allow you to adjust the rack height, which helps limit variations in alignment during suspension movements.
AVP Accuracy: The two shims can be different...
In stock
Inspection hatch for WEBER 40DCOE and 45DCOE
Number 80 on exploded view
In stock
In stock
In stock
Center distance of the cabochon fixing screws: 89mm
Suitable for A110 / R5 Turbo Maxi
In stock
Same as original capacity: 26 liters
Suitable for:
R4/4L : From 1961 to September 1974
In stock
In stock
sold with the water pump joint
In stock
In stock
In stock
The sets are supplied with the following components:
Cylinder Heads (x4)
Domed Pistons (x4)
Rings (x12)
Pin (x4)
Circle Clips (x8)
Dimensions of the various parts:
Cylinder Head Bore Diameter: Ø 77.75mm
Cylinder...
In stock
Segment Characteristics:
Segment Diameter: Ø 65mm
Thickness of Upper Segments (Fire-resistant): 2mm
Thickness of Intermediate Segments (Waterproof): 2mm
Lower piston ring thickness (scraper): 3.5mm
It is...
In stock