- Sold with drill bit holder
- Includes 5 drill bits in each of the following sizes:
- 0.6mm
- 0.7mm
- 0.8mm
- 0.9mm
- 1.0mm
- 1.1mm
- 1.2mm
- 1.3mm
- 1.4mm
- 1.5mm
- 1.6mm
- 1.8mm
- 2.0mm
- 2.1mm
- 2.2mm
- 2.3mm
- 2.4mm
- 2.5 mm
- 2.6mm
- 2.8mm
- 3.0mm
- 3.2mm
Out of stock
Tool for adjusting float clearance 8 / 9mm
Reference:
48105
- Allows easy adjustment of the float with one side of the tool calibrated to 8mm and the other side to 9mm.
- Allows direct action on the float tab thanks to a slot at the end of the tool.
€24.00
(tax incl.)
Order before 1pm and enjoy same day shipping !
You may also like
- Allows control of nozzle calibration
- Graduation is 0.10 mm in 0.10 mm increments, with a minimum of 1.5 mm to 3.00 mm and a maximum of 1.5 mm.
In stock
- Allows control of nozzle calibration
- Graduation is 0.05 mm in 0.05 mm increments, with a minimum of 0.45 mm and a maximum of 1.5 mm.
In stock
- Allows easy adjustment of the float with one side of the tool calibrated to 5mm and the other to 6mm.
- Allows direct action on the float tab thanks to a slot at the end of the tool
In stock
Customers who bought this product also bought:
In stock
In stock
- Suitable for WEBER 40DCOE and 45DCOE carburetors
- M5x32 screw
- Head width 8mm
- Number 52 on exploded view
- Compatible with other WEBER carburetors, see below
In stock
- Suitable for WEBER 40 DCOE carburetor
- Tune extends from the carburetor: 15mm
- Carburetor mounting via stud and nut
- Mounting hole spacing: 66mm
- Allows the installation of high-performance filters (AVP48099 or AVP48100) and sock filters (AVP48103)
- Ideal for competition use
For installation with new generation venturis (Ref. AVP48084 or AVP48085), the spacer (AVP48087) is recommended
to fill the space between the auxiliary venturi and the carburetor body.
Ideal velocity stack for mounting an R5 Alpine engine with two Weber 40 DCOE carburetors in an Alpine A110 with a large chassis
In stock
- Suitable for WEBER 40DCOE carburetors (First and last generation)
- This spacer fills the gap between the 4.5 venturi outlet and the carburetor body.
- It allows the installation of screw-on aluminum velocity stacks (AVP48091 and AVP48092) or a installation without a velocity stack
- This spacer is necessary if you are using the 4.5 venturis (AVP48084 or AVP48085) without the 55mm push-in air intake velocity stacks (AVP48093)
- Spacer mounting diameter: Ø 45 mm (Tolerance +0.10 mm)
Caution: Some carburetors have irregularities in their internal machining of the body. In this case, it may be necessary to make adjustments to certain spacers to precisely fit them to the carburetor bodies.
In stock
In stock
- Stainless steel airbox: high corrosion resistance and durability
In stock
- Kit of 4 springs for locking the venturi in the body of the WEBER DCOE 40 and DCOE 45 carburetor
- For first generation Caburator WEBER
In stock