Complete engine gasket kit "Large bearing" (73mm bore) - 1289cc engine (Type 810) - R12 / A110 V85

Suitable for the following vehicles:

• R4 / 4L: Type R1120: from chassis number 954001: from 10/1968
• R4 / 4L: Type R1123: from chassis number 627132: from 07/1968
• R4 / 4L: Type R1126: from 1971
• R4 / 4L Safari: from 1971
• R4 / 4L GTL: Type R1128: from 1978
• R4 Rodeo: from 1970
• R4 Van: Type R2105: from chassis number 59996: from 10/1968
• R4 Van: Type R2106: from chassis number 25950: from 10/1968
• R4 Van: Type R2108 - R2109 - R2391 - R2392: from 1970
• R4 Van: Type R2340 - R2370 - R2430: from 1975
• R5 All models (except Alpine and Alpine Turbo): from 1972 -> 1985
• R5 RODEO (Theilhot): from 1982 -> 1985
• R6: from 05/1968
• R6 RODEO: from 1973
• R7: All models

• Cooling fan: Pusher or Puller
• Universal Spal connector (requires modification depending on specific vehicle wiring)
• Observe correct wiring polarity for fan rotation:
• Fan in puller mode: Red (+ Battery) / Black (- / Ground)
• Fan in pusher mode: Red (- / Ground) / Black (+ Battery)
• Fan supplied as a standalone unit; mounting or fixing kit not included.
• See fan dimensions in photo #2

• Bore diameter: Ø 55mm (Minimum) to Ø 170mm (Maximum)
• Stone dimensions: 100mm
• Interchangeable honing stone
• Self-adjusting and tightening sanding arm with flexible drive for pneumatic or electric drills
• For honing, sanding, and cleaning cylinders, tubes, bores, etc.

Caractéristiques des segments :

• Diamètre des segments : Ø 73mm
• Épaisseur des segments supérieurs (Coupe-feu): 1.75mm
• Épaisseur des segments intermédiaires (Étanchéité): 2mm
• Épaisseur des segments inférieurs (Racleur): 4mm

Il est indispensable d'effectuer une vérification du jeu à la coupe de chaque segment avant leur mise en place sur les pistons, selon les valeurs données par le constructeur ou données dans la notice fournie.

Au montage, la coupe des segments doit être répartie de façon régulière sur le périmètre du piston à 120°.

Suitable for vehicles with 1397cc engines (Type 847.20, C1J, C2J, C3J):

• • R5 TS / TX / GTL / Automatic / USA
  • R11 L / TL / TLE
  • R18 TL / GTL
  • Fuego / Express

Kits are supplied with the following:

• • Cylinder Cylinders (x4)
  • Pistons (x4)
  • Ring Rings (x12)
  • Crankshafts (x4)

Dimensions of the different parts:

• Bore diameter of the cylinder liners: Ø 76mm
• Flange or top diameter of the cylinder liners (D): Ø 90.10mm
• Base diameter of the cylinder liners (A): Ø 80.60mm
• Overall height of the cylinder liners (C), including skirts: 134mm
• Height from the top of the cylinder liner to the base gasket area (E): 95mm
• Dimensions of the shafts: Ø 20 x 63.50 mm (Cirlip-free mounting)
• Segment thickness: 1.75 mm / 2 mm / 4 mm (Fireproof/Sealing/Scraper)
• Base gasket type: O-ring

Piston mounting direction: an arrow drawn perpendicular to the piston axis is shown on the top of the piston. It must be oriented in the direction of engine rotation during the connecting rod's downward stroke (see manufacturer's instructions or diagram).

It is essential to check the ring end gap of each piston ring before installing them on the pistons, according to the values ​​given by the manufacturer or in the supplied instructions.

During installation, the ring end gap must be evenly distributed around the piston circumference at 120° intervals. 

Seal Dimensions:

• White Seal Thickness: 0.06mm
• Black Seal Thickness: 0.07mm
• Red Seal Thickness: 0.09mm
• Kit of 12 seals: x4 White / x4 Black / x4 Red
• Seal Diameter: Ø 78.4x86mm
• Renault OE Reference: 7700508287 (x4) + 7700508288 (x4) + 7700510472 (x4)