In stock
Carburetor & Carburetor Parts CG
CG Carburetor Spare Parts
Are you restoring or maintaining a CG? At AVP, find a complete range of carburetors and spare parts suitable for original or tuned engines. Each part is selected to ensure reliable fuel delivery and precise adjustment of your carburetion system. Spare parts available for CG carburetion:
- Complete carburetors such as Weber (DCOE) and Solex, based on period assemblies
- Complete gasket kits for overhauling your carburetors
- Jets (main, idle, pump) for custom tuning
- Floats and needles for fuel tank level control
- Richness screws, springs, and internal adjustment components
- Flanges, intake manifolds, and controls Accelerator pedals
- Accessories: axles, levers, pump rods, integrated filters
- Carburetor-specific maintenance and synchronization tools
Whether your CG is intended for road use or historic racing, our components ensure reliable assembly, respecting the original spirit or for more advanced preparation.
In stock
Center distance between flange and intake manifold (Side without stud): 32mm and 102mm
Center distance between flange and carburetor (Side with stud): 92mm and 60mm
Flange thickness: 17.5mm
Pipes diameter: Ø 36.5mm...
Out of stock
In stock
In stock
Out of stock
In stock
Out of stock
Out of stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
M5X22 screws
Sold individually, requires 9 pieces for one carburetor
Number 5 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Lower bowl cover gasket AVP48118
Number 36 on exploded view
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Number 83 on exploded view
In stock
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors,
For 23g or 26g brass or plastic float,
Requires 1 piece per carburetor,
Number 72 on the exploded view,
Also suitable for the following carburetors: DCOE, DCO/SP,...
In stock
In some configurations, Weber DCOE carburetors are positioned directly above the exhaust, which can create vapor lock problems due to heat: our AVP48010 plate can solve this problem
Plate can be covered with thermal...
In stock
For M12 banjo bolts
Number 70 on exploded view
In stock
For M12 banjo bolts
Number 98 on exploded view
In stock
M12 Banjo Bolt
Sold individually without gasket
Number 70 on exploded view
In stock
Banjo screw M12
Sold individually without gasket
In stock
Gasket dimensions: Ø 20x12x1mm
Suitable for WEBER 40DCOE and 45DCOE carburetors
Number 2 and number 69 on exploded view
Sold individually, 1 piece required for one carburetor
Compatible with other WEBER carburetors,...
In stock
Joint dimensions: Ø 20x16x1mm
In stock
The kit consists of:
"T" fuel connector x1
90° elbow fuel connector x1
Banjo connector screw x2
Banjo screw under head seal x2
Banjo screw lower seal x2
Hose clamp: Size 12-14mm x3
In stock
The kit consists of:
90° elbow fuel connector x1
Banjo connector screw x1
Banjo screw under head gasket x1
Banjo screw lower gasket x1
Hose clamp: Size 12-14mm x1
In stock
Sold individually, 1 cover required per carburetor
Number 4 on exploded view
In stock
In stock
Suitable for WEBER 40DCOE and WEBER 45DCOE carburettor
Thread16x1.5
Need 1 piece for a carburetor
Number 1 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
Requires 1 part per carburetor
Number 3 on exploded view
Compatible with other WEBER carburetors, see below
Out of stock
In stock
In stock
Intake manifold mounting distance: 70mm and 110mm
Carburetor mounting distance: 110mm and 70mm
Flange thickness: 19.3mm
Pipes diameter: Ø 40mm
Flanges supplied with O-rings (x4), paper gaskets (x4), and mounting...
In stock
In stock
In stock
Intake manifold mounting distance: 70mm and 110mm
Carburetor mounting distance: 110mm and 70mm
Flange thickness: 19.3mm
Pipes diameter: Ø 45mm
Flanges supplied with O-rings (x4), paper gaskets (x4), and mounting...
Out of stock
In stock
In stock
Supplied with 4 carburetor mounting studs
Carburetor mounting stud distance: 110mm and 70mm
The carburetor is mounted directly onto the manifold. A seal is ensured by two paper gaskets; there is no need to use...
In stock
Supplied with x8 mounting studs and x4 O-rings (AVP4806) between the manifold and the carburetor.
Carburetor mounting stud distance: 110mm and 70mm
The carburetors are mounted directly onto the manifold. A...
In stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
External mounting
Fixes to the carburetor cover
Out of stock
Suitable for WEBER 40DCOE and 45DCOE carburetors
M5x32 screw
Head width 8mm
Number 52 on exploded view
Compatible with other WEBER carburetors, see below
In stock
Levier de commande d'accélérateur pour UN carburateur WEBER 40DCOE ET 45DCOE
Adaptable sur R8 et Alpine A110 avec pipe pour un carburateur WEBER
Dimension du centre de l'arbre au centre de la rotule: 23,50 mm
Rotule...
In stock
Throttle control lever for TWO WEBER 40DCOE AND WEBER 45DCOE carburetors
Allows carburetor synchronization
Suitable for R8 Gordini, Alpine A110, Simca Rallye
8mm diameter ball joint
In stock
Intake ducts: Ø 33mm
Out of stock
Suitable for WEBER 40DCOE carburetor
Extension length from the carburetor = 25mm
Stud/nut mounting
Allows the installation of high-performance filters REF 48099 or 48100
Also suitable for AVP stock filter ref 48103...
In stock
Aluminum air intake horn/trumpet for WEBER 40DCOE carburetor
43mm extension over the carburetor
Stud/nut mounting
Allows installation of high-performance filter REF 48099 or 48100
Also suitable for AVP sock filter...
In stock
Air intake horn/trumpet for WEBER 40DCOE carburetor
Extension length from the carburetor: 55mm
ATTENTION: Must be fitted with venturi REF 48084 or 48085
Fixing with kit REF 48097
Suitable for fitting AVP filters ref...
In stock
Air intake horn/trumpet for WEBER 40DCOE carburetor
Extension length from the carburetor: 75mm
ATTENTION: Must be installed with venturi REF AVP 48084 or 48085
Fix with kit REF 48097
Suitable for mounting AVP filters...
In stock
Allows to clamp the horns on the body of the WEBER 40DCOE carburetor
ATTENTION: essential for REF 48093 horns
Kit for a carburetor consisting of 4 stop tabs, 4 washers and 4 nuts
Also suitable for WEBER 42DCOE...
In stock
Air intake horn/trumpet filters for WEBER 40DCOE carburetor
Fitment possible on all AVP air intake horns
Mesh filters that feature two layers of stainless steel mesh with a filter layer in between to ensure maximum...
In stock
Suitable for Cornet/Air intake trumpet of the Weber DCOE 40 carburetor,
Fixing by screw necklace on rubber flange for perfect sealing,
Possible assembly on all AVP cornets for DCOE40,
Overall length: 115mm,
Diameter:...
In stock
Installation possible on all AVP horns
Length 115mm (can be cut to size)
Clamp included
Sold in pairs
In stock
In stock
In stock
In stock
Suitable for WEBER 45DCOE carburetor
Extension length from the carburetor = 48mm
Stud/nut mounting
Allows installation of AVP high-performance filter part number 48101 or 48102
Also suitable for AVP sock filter part...
In stock
Aluminum air intake horn/trumpet for WEBER 45DCOE carburetor
48mm extension over the carburetor
Stud/nut mounting
Allows installation of high-performance filter REF 48101 or 48102
Also suitable for AVP sock filter...
In stock
Air intake horn/trumpet for WEBER 45DCOE carburetor,
Extension length from the carburetor: 62mm,
ATTENTION: Must be installed with venturi REF 48086,
Fixing with kit REF 48098,
Suitable for mounting AVP filters REF...
In stock
Allows to clamp the horns on the body of the WEBER 45DCOE carburetor
ATTENTION: essential for REF 48096 horns.
Kit for a carburetor consisting of 4 stop tabs, 4 washers and 4 nuts
Also suitable for WEBER 48DCOE...
In stock
Air intake trumpet filter for WEBER 45DCOE carburetor
Fitment possible on all AVP trumpets
Mesh filters that feature two layers of stainless steel mesh with a filter layer in between to ensure maximum engine...
In stock
Suitable for Weber DCOE 45 carburetor air intake horn/trumpet
Fixed with a screw collar on a rubber flange for a perfect seal
Can be fitted to all AVP DCOE45 air intake horns/trumpets
Overall length: 115mm
Diameter:...
In stock
In stock
In stock
Fits WEBER 40DCOE first and latest generation carburetors
This spacer is required if you are using the REF 48084 or REF 48085 venturis without the AVP 55mm air intake nozzles, part number 48093
It fills the gap...
In stock
Suitable for WEBER 40DCOE carburetors with spring lock,
Suitable for first-generation WEBER 40DCOEs with 55mm air intake nozzle REF 48093,
WARNING: If you are not using the 55mm air intake nozzle REF 48093, you must...
In stock
Suitable for Latest generation WEBER 40DCOE carburetor with 55mm air intake nozzle REF 48093
WARNING: If you are not using the 55mm air intake nozzle REF 4093, you must use the spacer REF 48087 to fill the gap...
In stock
Suitable for WEBER 45DCOE carburetor with needle screw locking
Allows the installation of 62mm air intakes/trumpets REF 48096
Installation possible on older-generation carburetors with spring-locked venturis provided...
In stock
Kit of 4 springs for locking the venturi in the body of the WEBER DCOE 40 and DCOE 45 carburetor
For first generation Caburator WEBER
In stock
WARNING: Suitable for Venturi ref 48085 and ref 48086 for WEBER 40DCOE and 45DCOE carburetors.
Allows you to stop the movement of the venturi for older generation DCOEs, and stop the movement of the nozzle and...
In stock
Brake for venturi locking screw for carburettor WEBER 40DCOE and 45DCOE latest generation
Number 24 on exploded view
In stock
Suitable for all types of WEBER 40DCOE carburetors
In stock