Kit specifications (Tie rods / Ball joints and boots):
Ball joint taper diameter (Steering knuckle side): Top of taper Ø 11mm / Bottom of taper Ø 12mm
Ball joint taper stud thread diameter: M10 x 1.25 (right-hand...
In stock
Steering and front axle A110 1600 (SC / SI / SX)
In stock
Caractéristiques de la rotule :
Diamètre du cône de la rotule (Côté pivot) : Haut du cône Ø 11mm / Bas du cône Ø 12mm
Diamètre du filetage de l'axe du cône de la rotule : M10 x 125 (pas à droite)
Diamètre du filetage...
In stock
In stock
Suitable for:
R8 (All models) / Caravelle / Floride S: Left and Right Side Boot
A110 (All models) / Alpine GT4: Left and Right Side Boot
A310.4: Left and Right Side Boot
A310 V6: Left Side Boot
Matradjet: Left and...
In stock
Out of stock
Suitable for:
Eye end cap of rack and pinion - Ref 0824373600 / 7700504987
Front tie rod end cap or rear tie rod end cap - A110 - Ref 7700504987
Exhaust hanger - A310 V6 - Ref 7700504987
Inner diameter of the eye: Ø...
In stock
In stock
Flexor Specifications:
Mounting hole spacing:4 x 50.50 mm
Mounting hole diameter: Ø 8.4 mm
Center hole diameter:Ø 10.50 mm
Flexor thickness: 11 mm
Material:Rubber flexor with metal reinforcement
Supplied with 4 x...
In stock
In stock
The supplied ring allows the Ø 17x5x10mm bearing to be installed on the rack and pinion gears
In stock
In stock
In stock
Ideal rack reinforcement to improve rack support for increased rigidity and steering precision
Suitable for:
Alpine A110 VD: SC and SI
Alpine A110 VH: SX
In stock
M8 Hexagon Head Screw
For adjustable rack support: AVP 4612
In stock
In stock
In stock
In stock
In stock
Plate comes complete with mounting hardware.
Black cataphoresis treatment for optimal finish and corrosion resistance.
In stock
Out of stock
Not suitable for replacing the original ball joint bellows
In stock
In stock
In stock
In stock
In stock
In stock
In stock
The kit contains:
4 x 8mm smooth-bore screws - M8 thread (to be positioned on the wheel side)
4 x 8.4mm smooth-bore screws - M8 thread (to be positioned on the body or chassis side)
Alpine / Renault OE Ref:...
In stock
This washer is positioned on the screw opposite the eccentric nut
Thick washer M8
Washer outer diameter: Ø 23mm
Sold individually; one washer is required per side.
In stock
Renault OE Ref: 1081200866
In stock
In stock
Axle specifications:
Smooth shaft diameter: Ø 16mm
Thread diameter: M14x200 (right-hand thread)
Smooth shaft length: 15.8cm
Overall length: 25.2cm
Supplied individually, without nut
Suitable for:
4CV: Post-1956...
In stock
Suitable for:
4CV: After 1956
Dauphine: Lower and Upper Wishbone Axle (Chassis Side)
R8 / R8S / R8G
Caravelle / Floride S
A106 / A108
A110
Matradjet
In stock
Bolt specifications:
Smooth shank diameter: Ø 14mm
Thread diameter: M12x1.25 (right-hand thread)
Length under head: 15.8cm
Total length: 16.2cm
Supplied individually, without nut
Suitable for:
R8 / R8S / R8G...
In stock
In stock
In stock
Out of stock
Out of stock
In stock
In stock
Cap Dimensions:
Inner Diameter: Ø 40mm
Outer Diameter: Ø 42mm
Height: 26.5mm
Also suitable for some R16 (R1150) models with rear drum brakes.
In stock
In stock
In stock
Out of stock
In stock
In stock
In stock
In stock
Out of stock
In stock
Out of stock
Screw M8x125
Total length under head: 20.5mm
In stock
In stock
Dimensions:
- Length 145mm
- Interior Ø 46mm and Ø of the rod 10mm
In stock
Ces amortisseurs hydrauliques bi-tube, conçus pour une utilisation normal de type "Route".
Avec un tarage confort proche des amortisseurs d'origines, ceux-ci sont parfaits pour l'usage au quotidien.
Caractéristiques...
In stock
These twin-tube hydraulic shock absorbers are designed for versatile use, including road and rally driving.
With a firmer damping than conventional shock absorbers, these are perfect for sportier driving, while still...
In stock
Spacer dimensions:
Inner diameter: Ø 72mm
Recess diameter: Ø 88mm
Outer diameter: Ø 108mm
Spacer thickness: 16mm
Sold individually
Designed for installation only with original springs featuring a wire diameter of...
In stock
Spacer dimensions:
Inner diameter: Ø 66mm
Recess diameter: Ø 76mm
Outer diameter: Ø 108mm
Spacer thickness: 16mm
Sold individually
Designed for use only with springs made from Ø 13.5mm wire
In stock
In stock