The sets are supplied with the following components:
Cylinder Heads (x4)
Domed Pistons (x4)
Rings (x12)
Pin (x4)
Circle Clips (x8)
Dimensions of the various parts:
Cylinder Head Bore Diameter: Ø 59.95mm
Cylinder...
In stock
Performance & Racing parts Dauphine
Our performance and racing spare parts for your Renault Dauphine
Discover here a wide choice of parts and accessories designed to improve and boost the performance of your Dauphine
Whether you are looking for electronic ignition, iridium spark plugs, rear tie rods, a sports-prepared camshaft, oil pan, exhaust manifold, sports silencer, steering rod, manual choke, circuit breaker....at AVP, Arnaud Ventoux Pièces, you will find everything you need to optimize the operation of your old car with quality components.
In stock
Segment Characteristics:
Segment Diameter:Ø 60mm
Thickness of Upper Segments (Fire-resistant): 1mm
Thickness of Intermediate Segments (Waterproof): 1.20mm
Low ring thickness (Scraper): 2.50mm
It is essential to...
In stock
Sheets (x4)
Sheet Dimensions:
Sheet Bore Diameter: Ø 59.95mm
Sheet Flange or Top Diameter (D): Ø 72.75mm
Sheet Base Diameter (A): Ø 62.40mm
Sheet Height (including skirts, overall) (C): 121mm
Sheet Height to Base...
In stock
Return your old camshafts clean and without bites before ordering
Out of stock
For mounting a belt width: 13mm
Groove for a 5mm key
A steel collar is installed on the oil seal surface for improved sealing and reduced pulley wear.
In stock
Threaded spigot diameter: M16x150
This assembly can be made from engine No. 958967 (early April 1960) on Ventoux Type 670 engines.
Out of stock
In stock
In stock
In stock
Minimum insertion diameter of the plug (with its gasket) between:Ø 48.5mm and Ø 50mm
Rock cover plugwith vent hole
Plug sold with its sealing gasket (AVP 60119)
In stock
Minimum insertion diameter of the plug (with its gasket) between:Ø 48.5mm and Ø 50mm
Rock cover plugwith vent hole
Plug sold with its sealing gasket (AVP 60119)
In stock
Possible mounting on the 4CV / Dauphine and Dauphine Gordini cylinder head (aligned or offset mounting holes)
Intake manifold inner diameter: Ø 29mm
Exhaust manifold inner diameter: Ø 29mm
Outlet inner diameter: Ø...
Out of stock
In stock
Possible mounting on the 4CV / Dauphine and Dauphine Gordini cylinder head (aligned or offset mounting holes)
Intake manifold inner diameter: Ø 29mm
Exhaust manifold inner diameter: Ø 29mm
Outlet inner diameter: Ø...
In stock
Silencer supplied with 1 connecting pipe with adjustable height flange (For original manifold and Autobleu manifold)
Silencer inlet pipe height: 10cm
Inner diameter of the pipe at the silencer inlet: Ø 45mm
Inner...
Out of stock
Silencer supplied with 1 connecting pipe with adjustable height flange (For original manifold and Autobleu manifold)
Silencer inlet pipe height: 10cm
Inner diameter of the pipe at the silencer inlet: Ø 45mm
Inner...
Out of stock
Out of stock
Out of stock
These bushings replace the original bushings; no modifications are required.
Out of stock
In stock
Out of stock
In stock
The rear tie rod mounting allows for reduced movement of the "trumpets", providing the vehicle with improved handling on the rear axle.
In stock
Brake Disc Specifications:
Outer Diameter: Ø 260mm
Inner Centering Diameter: Ø 60mm
Mounting Hole Spacing: 71mm
Disc Offset: 33.5mm
Brake Disc Thickness: 7.5mm (Solid Disc)
Sold in pairs (2 discs)
Important: Brake...
In stock
4CV: Drum brake (From 06/1953 until end of series)
Alpine A106: Drum brake
Dauphine (All models): Disc brake
Caravelle / Florida: Disc brake
R10 / R8 (All models): Disc brake
Alpine A110 and GT4: Disc brake
Matradjet:...
In stock
In stock
Out of stock
In stock
In stock
In stock
This lighter is suitable for:
- 4CV / Dauphine / Estafette / Juva 4 / R4 (1st model)
- Engine 622 / 668 / 670 / 670-3
Same as Ducellier: 566 / 3910 / 2175 / 4037 / 4065 / 4076 / 4094
Kit to be used with a primary...
In stock
Sold individually
12V-55W H3 bulb supplied
Out of stock
In stock
Out of stock
