In stock
Matra Djet Engine and Transmission Performance
Our performance and Racing spare parts for the engine of your Matra Djet
Discover here a wide range of parts and accessories designed to improve and boost the performance of your Matra Djet
engine
Whether you are looking for electronic ignition, iridium spark plugs, rear tie rods, a sports camshaft, an oil pan, an exhaust manifold, a sports silencer, steering rods, a manual choke or a circuit breaker, at AVP, Arnaud Ventoux Parts, you will find everything you need to improve the performance of your vintage vehicle with quality components.
For mounting a belt width: 13mm
In stock
For mounting a belt width: 13mm
In stock
A steel fret is fitted on the surface of the oil seal for better sealing and reduced wear on the pulley.
For fitting a belt width: 13mm
In stock
Please note: This oil pump is not suitable as a replacement for an original oil pump in an original sheet metal oil pan for 1255cc and 1296cc engines.
Height from the oil pump mating surface to the bottom of the...
In stock
In stock
In stock
Supplied with self-adhesive thermal protection to stick on the most suitable side depending on the assemblies.
In stock
The oil filter sandwich plate fits between the oil filter and the engine block.
It offers improved oil flow thanks to wider, unrestricted internal channels, making it ideal for installing an additional oil cooler....
In stock
In stock
Please note this hose cannot replace the original oil hoses, use only to carry out an adaptable assembly using a connector and a new radiator.
Material: Black synthetic braid
Maximum operating pressure 35 bar and...
In stock
Please note this hose cannot replace the original oil hoses, use only to carry out an adaptable assembly using a connector and a new radiator.
Material: Black synthetic braid
Maximum operating pressure 35 bar and...
In stock
In stock
Out of stock
In stock
Out of stock
Sold with water pump gasket
Distance between two pulley mounting bolts (Center-to-center):50mm
Pulley mounting using x4 M8 bolts (Not supplied)
The high-flow water pump increases performance Cooling without any...
In stock
Suitable for:
Simca 1000 / 1200S / R1 / R2 / R3 / CG - Ref 22089M
Renault R8 / R8G / Floride / Caravelle
Alpine GT4 / A110 (1100Cm³ / 1300cm³)
Matradjet
These bearings are only suitable for old generation water...
In stock
Suitable for (Engine Type 688 / 689 / 810):
R4 / R6 / R8
Caravelle - Matra Jet
R12.TL - R12.TS - R15.TL
A110.V85 (810) - A110.GT4
This distributor must be used with a coil with a primary resistance between 2.5...
Out of stock
This lighter is suitable for:
- R8G / A110 (1108cc / 1255cc / 1296cc)
Kit to be used with a primary resistance coil between 2.5 and 3.5 ohms
Compatible with AVP4708 and AVP4715 coils
Out of stock
Kit to be used with a coil of primary resistance between 2.5 and 3.5 ohms
Compatible with coils AVP4708 and AVP4715
Compatible for Ducellier igniter with an inner body diameter of Ø 58.8mm
Not suitable for an igniter...
In stock
Kit to be used with a coil of primary resistance between 2.5 and 3.5 ohms
Compatible with coils AVP4708 and AVP4715
Compatible for Ducellier igniter with an internal body diameter of Ø 58.8mm
Not suitable for an...
In stock
Built-in short extensions
Straight coil terminal
Coil wire length: 50cm
This ignition harness consists of 4 spark plug wires and 1 coil wire.
We would like to point out that our spark plug wires are made with 7 mm...
In stock
Built-in short extensions
Straight coil terminal
Coil wire length: 50cm
We would like to point out that our spark plug wires are made with Ø 7mm silicone wire and a standard copper core (wire material), which means...
In stock
Built-in short extensions
Straight coil terminal
Coil wire length: 50cm
This ignition harness consists of 4 spark plug wires and one coil wire.
We would like to point out that our spark plug harnesses are...
In stock
Ideal for prepared engines or to replace a mechanical fuel pump.
Flow rate: 125l/h
Max pressure: 0.30bar
Suction: -0.10bar
220° adjustable inlet and outlet tube: Ø 8mm
Self-regulated fuel pump
Dimensions: 73x126mm /...
In stock
Ideal for prepared engines or to replace a mechanical fuel pump.
Flow rate: 130l/h
Max pressure: 0.15bar
Suction: -0.20bar
220° adjustable inlet and outlet tube: Ø 8mm
Self-regulated fuel pump
Dimensions: 73x126mm...
In stock
In stock
FACET Silver Top 113 l/h Fuel Pump (476087) self-regulating with integrated fuel filter
These pumps reduce the "Vapor Lock" effect by allowing for a more consistent fuel supply.
They must be mounted in a vertical...
In stock
FACET Silver Top 113 l/h Fuel Pump (476087) self-regulating with integrated fuel filter
These pumps reduce the "Vapor Lock" effect by allowing for a more consistent fuel supply.
They must be mounted in a vertical...
In stock
Fitting Specifications:
Inlet Thread Diameter: 1/8 x 27 NPTF
Outlet Diameter: Ø 8mm
Orientation: 90° Elbow
Material: Brass
Sold individually
Suitable for Facet fuel pumps of the following types: Silver Top / Red Top...
Out of stock
Fitting Specifications:
Inlet Thread Diameter: 1/8 x 27 NPTF
Outlet Diameter: Ø 8mm
Orientation: Right
Material: Brass
Sold individually
Suitable for Facet fuel pumps of the following types: Silver Top / Red Top and...
In stock
Fuel filter with 74-micron filtration
Filter diameter: 40mm
Filter height: 35mm
Suitable for Facet fuel pumps of the following types: Silver Top / Red Top and Gold-Flo
In stock
Seal Diameter: Ø 24x51 mm
Seal Thickness: 3 mm
Material: Specific hydrocarbon rubber
Suitable for Facet fuel pumps of the following types: Silver Top / Red Top and Gold-Flo
Seal must be replaced each time the pump...
In stock
This silent block kit is used for mounting Facet pumps and allows the pump to be fixed to the body, preventing vibrations.
Suitable for Facet fuel pumps of the following types: Silver Top / Red Top and Gold-Flo
Kit...
In stock
Glass bowl Ø 67mm
Filter element: Interchangeable paper cartridge
One inlet: dual size 6 and 8mm
One outlet: dual size 6 and 8mm
Regulation pressure: Regulation range from 0 to 0.6 bar
Compatible with fuel SP95 /...
In stock
Glass jar Ø 67mm
Filter element: Replaceable paper cartridge
One Inlet: dual size 6 and 8mm
One Outlet: dual size 6 and 8mm
Regulating pressure: Regulating range from 0 to 0.6 bar
Compatible with SP95 / SP98 / E85...
In stock
Intake manifold mounting distance: 70mm and 110mm
Carburetor mounting distance: 110mm and 70mm
Flange thickness: 19.3mm
Pipes diameter: Ø 40mm
Flanges supplied with O-rings (x4), paper gaskets (x4), and mounting...
In stock
In stock
In stock
Carburetor mounting distance to the intake manifold: 110mm and 70mm
Manifold supplied with O-rings (x2) and studs (x4) for mounting the carburetor
The carburetor is mounted directly onto the manifold. The seal is...
In stock
Stainless steel airbox: high corrosion resistance and durability
In stock
45mm Clip for Stainless Steel Airbox
Material: Stainless Steel
Sold individually
Suitable for:
Weber 40 DCOE carburetor
Weber 40 DCOM carburetor
In stock
In stock