In stock
Best sellers
In stock
Alpine OE ref: 6000000216 / 6000000589 / 6000000591 / 6000001374 / 6000047593
In stock
To wrap around an R4/4L, six meters of reed are needed, with about 30 cm of margin.
In stock
Suitable for:
A310.V6: Upper and lower rear wishbone - All models (pre and after 1980)
R5 Turbo: Upper and Lower Rear Triangle
Out of stock
Heat treatment 60 HRC on 1mm depth
Ref OE Renault : 7700618536 / 7700658371 / 6001002128
In stock
In stock
In stock
End cap for stop switch Ø 12.5mm
Mounting using a long rod
In stock
Suitable for:
Eye end cap of rack and pinion - Ref 0824373600 / 7700504987
Front tie rod end cap or rear tie rod end cap - A110 - Ref 7700504987
Exhaust hanger - A310 V6 - Ref 7700504987
Inner diameter of the eye: Ø...
In stock
Suitable for:
Dauphine (All models): Drum brake
Florida / Alpine A108: Drum brake
In stock
In stock
Out of stock
In stock
Outer diameter: Ø 22mm
Wire diameter: Ø 2.5mm
Free length: 38mm
Total number of turns: 8
Sold individually
In stock
Brake master cylinder: 4CV (2nd Model) / Dauphine / Floride / Alpine A108
Clutch transmitter: Matra Djet
In stock
In stock
Primary winding resistance: 2.8 ohms
Secondary winding resistance: 7900 ohms
Coil compatible with electronic ignition kits Ref AVP4798 and Ref AVP4799
Out of stock
In stock
Suitable for:
Simca 1000 (All models) / R1 / 1200S
R15 (TS) / R16 (Types L / TL / TS / TX) / R17 TL / TS) : 1600cm³ engine
In stock
Ring Size:
Inner Diameter: Ø 21mm
Outer Diameter: Ø 24mm
Height: 30mm
Suitable for:
4CV (2nd Assembly): From 1956
Dauphine / Floride
Alpine A106 / A108
In stock
AVP recommends the reinforced gearbox side silentblocks Ref 4305, for reasons of reliability and ease of assembly.
Out of stock
Compatible for any Ducellier igniter with an inside diameter of the body of 58.8mm
In stock
In stock
Material: mixed fibers, acrylic and wool
Thickness: 6mm
Width: 1 meter
Sold by the linear meter
In stock
Pad Dimensions:
Pad Insert Diameter: Ø 18mm
Suction Cup Diameter: Ø 80mm
Pad Height: 26mm
Material: Rubber
Out of stock
In stock
In stock
In stock
Suitable for:
4CV (1st and 2nd models)
Dauphine (1st model)
Alpine A106
Water pump with 7 mounting holes, you have the possibility to make the 8th hole if necessary.
In stock
Need x7 staples per plate surround
In stock
To wrap around an R4/4L, six meters of reed are needed, with about 30 cm of margin.
In stock
In stock
In stock
Rubber boot made with a rubber compound designed to resist transmission oils and hydrocarbons
Sold individually, without the metal ring and oil seal
In stock
Screw: M11x150
Length under head: 138mm
Sold individually, 10 screws required per motor
In stock
Suitable for:
R8.G (1255cc and 1296cc Engine)
GT4 / Matradjet (1255cc Engine)
A110 1100G and 1300G
A110.1600 S / SC / SI
A310.4 1600VF (Injection) / R12.G / R17.G
Super 5GT Turbo
In stock
Useful length (L on photo diagram number 3): 17mm
Sold with the pin
OE Renault / Alpine Ref: 0705837200
In stock
In stock
Pressure : 0 - 6 bar
Release pressure : 0.60 bar
Thread: M14x150
If fitting the pressure transmitter to a 1397cc R5 Alpine (R1223) engine, use extension part number: AVP5091
In stock
In stock
rear light bulb
Culot 2 studs / quirky lugs
Dimensions: 25x47mm
Reference: 7701348018
due to the multitude of types of bulbs used, please check compatibility with your vehicle
In stock
In stock
In stock
In stock
In stock
Dowel Dimensions:
Dowel Thread: M12 ((125 Pitch / Class 10.9)
Dowel Head Diameter: Ø 19.50mm
Dowel Recess Diameter: Ø 14.30mm
Dowel Length Under Head: 33mm
Dowel Overall Length: 38mm
Suitable for:
Alpine A110 1300...
In stock
In stock