The sets are supplied with the following components:
Liners (x4)
Pistons (x4)
Rings (x12)
Panels (x4)
Dimensions of the different parts:
Liner bore diameter: Ø 76mm
Liner flange or top diameter (D): Ø 90.10mm...
In stock
R 11 Turbo engine - 1397cc engine (76mm bore diameter)
Rotor and Stator Pump (Trochoidal Pump) Height: 31mm
Strainer Height: 160mm at the highest point / 145mm at the lowest point (Measured from the engine block gasket surface to the strainer)
Renault OE Reference:...
In stock
Installing a plate in the oil pan reduces oil movement, ensuring consistent lubrication and reducing the risk of engine damage caused by insufficient lubrication during sharp changes of direction or turns.
Sold with...
Out of stock
Valve guide sold individually
Inner diameter of the guide: Ø 7mm
Outer diameter of the guide: Ø 11.23mm
Height of the guide: 41.5mm
Material: Gray cast iron
Suitable for:
R12 / R15: Intake and exhaust
A110 V85:...
In stock
Compatible avec :
R8G R1134 (Moteur 1108cm³ - Type 804) / R1135 (Moteur 1255cm³ et 1296cm³ - Type 812)
Alpine A110 1108cm³ / 1289cm³ (V85) / 1300G / 1300S
R5 Turbo 1 et 2 (1397cm³) / R5 Alpine Turbo / R5 Alpine...
In stock
Compatible with :
R8G R1134 (1108cm³ engine - Type 804) / R1135 (1255cm³ and 1296cm³ engine - Type 812)
Alpine A110 1108cm³ / 1289cm³ (V85) / 1300G / 1300S
R5 Turbo 1 and 2 (1397cm³)
R12.TS (1289cm³)
In stock
Engine block side thread: M20x150
Filter side thread: M20x150
Overall length: 50mm
In stock
Suitable for:
Super 5 GT Turbo (Phase 1 and 2)
Renault 11 Turbo (Phase 1 and 2)
Renault OE Ref: 7701349269 / 7700681418
In stock
Suitable for:
R8.G (1255cc and 1296cc Engine)
A110 1100G and 1300G
GT4 / Matradjet (1255cc Engine)
R12.G / R17.G (1600cc Engine)
Super 5GT Turbo and R11 Turbo: Cooler spark plug (1400cc Turbo Engine)
In stock
In stock
Sheet Dimensions: Length 50cm x Width 33cm
Sheet Thickness: 2mm
Ideal for making oil pan gaskets, timing case gaskets, and cylinder head cover gaskets. These gaskets must be installed with a light clamping force....
In stock
Sheet Dimensions: Length 50cm x Width 33cm
Sheet Thickness: 2.5mm
Ideal for making oil pan gaskets, timing case gaskets, and cylinder head cover gaskets. These gaskets must be installed with a light clamping force....
In stock
Sheet Dimensions: Length 50cm x Width 33cm
Sheet Thickness: 3mm
Ideal for making oil pan gaskets, timing case gaskets, and cylinder head cover gaskets. These gaskets must be installed with a light clamping force....
In stock
Sheet Dimensions: Length 58cm x Width 35cm
Sheet Thickness: 0.25mm
Ideal for making carburetor gaskets, fuel pump gaskets, engine and gearbox gaskets (Parts subject to low temperature or pressure). Suitable for all...
In stock
Sheet Dimensions: Length 58cm x Width 35cm
Sheet Thickness: 0.50mm
Ideal for making carburetor gaskets, fuel pump gaskets, engine and gearbox gaskets (Parts subject to low temperature or pressure). Suitable for all...
In stock
Sheet Dimensions: Length 58cm x Width 35cm
Sheet Thickness: 0.8mm
Ideal for making carburetor gaskets, fuel pump gaskets, engine and gearbox gaskets (Parts subject to low temperature or pressure). Suitable for all...
In stock
Sheet Dimensions: Length 58cm x Width 35cm
Sheet Thickness: 1mm
Ideal for making carburetor gaskets, fuel pump gaskets, engine and gearbox gaskets (Parts subject to low temperature or pressure). Suitable for all...
In stock
Sheet Dimensions: Length 58cm x Width 35cm
Sheet Thickness: 1.6mm
Ideal for making carburetor gaskets, fuel pump gaskets, engine and gearbox gaskets (Parts subject to low temperature or pressure). Suitable for all...
In stock
Sheet Dimensions: Length 50cm x Width 35cm
Sheet Thickness: 1.2mm
Ideal for making water seals, oil pumps, cylinder head cover gaskets, oil pan gaskets, and intake or exhaust manifold gaskets. Temperature limit:...
In stock
Piston diameter: Ø 53 mm (Minimum) to Ø 125 mm (Maximum)
Tool height: 75 mm
Supplied with a square tightening wrench
Ideal tool for installing pistons in the cylinder block
Out of stock
Bore diameter: Ø 55mm (Minimum) to Ø 170mm (Maximum)
Stone dimensions: 100mm
Interchangeable honing stone
Self-adjusting and tightening sanding arm with flexible drive for pneumatic or electric drills
For honing,...
In stock
Set of 3 replacement honing stones for expandable reamer/shroud: reference AVP T020
Stone dimensions: 100mm
In stock