- Levier de commande d'accélérateur pour UN carburateur WEBER 40DCOE ET 45DCOE
- Adaptable sur R8 et Alpine A110 avec pipe pour un carburateur WEBER
- Dimension du centre de l'arbre au centre de la rotule: 23,50 mm
- Rotule Ø 8mm
In stock
Nut brake for WEBER DCOE 40 / DCOE 45 and IDF carburetor
Reference:
48060
- Suitable for WEBER 40DCOE, 45DCOE and IDF carburetors
- Sold individually, requires 2 pieces per carburetor
- Number 31 on the exploded view
- Compatible with other WEBER carburetors, see below
€1.90
(tax incl.)
Order before 1pm and enjoy same day shipping !
Below are the different WEBER carburetors compatible with the AVP48060 reference:
|
Carburetor Inlet Diameter |
Type or model of Carburetor |
|---|---|
|
IDF, DCOE, DCO/SP, DCNF, IDA, ICEV |
|
| from Ø26 to Ø32 |
26/34 DHSA, 28/30 DHTA, 28/32 ADHA, 28/36 DHSA, 30 IBA, 30 DMTR, 30/32 DHTA, 30/32 DMTR, 32 ADF, 32 DAT, 32 DATR, 32 DATRA, 32 DFB, 32 DHS, 32 DHSA, 32 DMSA, 32 DMTR, 32 DMTRA, 32 IBA, 32 ICA, 32/34 DMTR |
|
from Ø34 to Ø45 |
34 ADF, 34 ADFA, 34 ADM, 34 DAT, 34 DATA, 34 DATC, 34 DATR, 34 DATRA, 34 DCHE, 34 DHS, 34 DMS, 34 DMTR, 35 DCNL, 36 DCA, 36 DCNFA, 36 DCNV, 36 DCNVA, 36 DCNVH, 38 ADLD, 40 DFO, 42 DFC, 45 DFC |
You may also like
- Throttle control lever for TWO WEBER 40DCOE AND WEBER 45DCOE carburetors
- Allows carburetor synchronization
- Suitable for R8 Gordini, Alpine A110, Simca Rallye
- 8mm diameter ball joint
In stock
- Suitable for WEBER 40DCOE and 45DCOE carburetors
- Sold individualy, requires 2 pieces per carburetor
- Number 32 on the exploded view
- Compatible with other WEBER carburetors, see below
In stock
- Suitable for older generation WEBER 45DCOE carburetors (the bearing surfaces differ from the shafts of modern versions)
- Caution: The throttle plates or flaps must be mounted using flat-head screws. (AVP48052)
- The mounting hole for the accelerator pump control must be drilled by the user, depending on the type of pump control.
- Overall shaft length: 180mm
- Thread diameter at the shaft ends: M7
- Part number 85 on the exploded view
In stock
- Suitable for older generation WEBER 40DCOE carburetors (the bearing surfaces differ from the shafts of modern versions)
- Caution: The throttle plates or flaps must be mounted using flat-head screws. (AVP48052)
- The mounting hole for the accelerator pump control must be drilled by the user, depending on the type of pump control.
- Overall shaft length: 180mm
- Thread diameter at shaft ends: M7
- Part number 85 on the exploded view
In stock
Customers who bought this product also bought:
Suitable for the following vehicles:
- R5 Alpine Atmo (R1223)
- R14: From 06/1983
- R18 GTX: From 02/1986
- R20 LS / TS / TX: From 12/1983
- R21 (J6R): From 03/1986 to 12/1995
- R25 (J6R - 706 / 707 / 762 / 763): From 01/1984 to 12/1992
- R30 TS / TX: From 08/1976->12/1983
- FUEGO GTX / TX: From 10/1980->10/1985
- Alpine A310 V6
In stock
- Suitable for WEBER 40DCOE and 45DCOE carburetors,
- For 23g or 26g brass or plastic float,
- Requires 1 piece per carburetor,
- Number 72 on the exploded view,
- Also suitable for the following carburetors: DCOE, DCO/SP, 40DCZ, IDF, 28/36 DCB, 28/36 DCD, 28/36 DCLD, 34 DCHD, 34 DCS, 36 DCD, 36 DCLD.
In stock
- Throttle control lever for TWO WEBER 40DCOE AND WEBER 45DCOE carburetors
- Allows carburetor synchronization
- Suitable for R8 Gordini, Alpine A110, Simca Rallye
- 8mm diameter ball joint
In stock
- Inlet / outlet connection: BSP 1/2" x14 (x2)
- Threaded sleeve: male Ø3/4" - 16UNF and female Ø3/4" - 16UNF
Please note, the oil filter plate does not correspond to the original hoses and fittings. Provide for the replacement of these fittings and hoses.
In stock
- Fuel pressure gauge kit.
- Allows fuel pressure adjustment with the "King" filter REF 6825.
- Graduation from 0.20g up to 1 bar.
- With connector and clamp for 6 or 8 diameter flexible hoses.
- The pressure gauge can be removed after adjustment and the cap provided in the kit can be screwed on for greater privacy in the engine compartment.
In stock
In stock
- Overall length: 245.5cm
- Sheath length: 193.5cm
- Cable length: 235cm
Suitable for:
- A110.1100 (VA and VB)
- A110.1300 (VA and VB)
- A110.1300 VC (V85)
Our cables are made in France and meet the assembly and quality standards of original equipment (OEM) cables from automotive manufacturers.
In stock