Click for more products.
No products were found.
Click for more products.
No products were found.
×
Black silicone ignition wiring harness with straight "NGK" connectors - 1
Black silicone ignition wiring harness with straight "NGK" connectors - 1
Black silicone ignition wiring harness with straight "NGK" connectors - 3
Black silicone ignition wiring harness with straight "NGK" connectors - 2
Black silicone ignition wiring harness with straight "NGK" connectors - 1
Black silicone ignition wiring harness with straight "NGK" connectors - 1
Black silicone ignition wiring harness with straight "NGK" connectors - 3
Black silicone ignition wiring harness with straight "NGK" connectors - 2
Black silicone ignition wiring harness with straight "NGK" connectors - 1
Black silicone ignition wiring harness with straight "NGK" connectors - 1
Black silicone ignition wiring harness with straight "NGK" connectors - 3
Black silicone ignition wiring harness with straight "NGK" connectors - 2

Black silicone ignition wiring harness with straight "NGK" connectors

Reference:
4L-711
  • This ignition harness consists of 4 spark plug wires and 1 coil wire, each 7mm in diameter.
  • It does not have interference suppression.

If the vehicle is equipped with sensitive electronic accessories, such as a radio, trip meter, monitor, or certain electronic ignition kits, interference or disruptions may occur.

  • Coil wire length: 550mm
  • Spark plug wire lengths: 300mm / 300mm / 350mm / 350mm

This type of harness includes a fiberglass core supporting a conductive and magnetic silicone sheath around it around which a stainless steel wire is wound.

This winding works on the principle of a coil; an induced voltage is created by the electromagnetic flux generated by the passage of high voltage through the core of the cable.

The magnetic field fluctuates within the cable, while the stainless steel wire wound around it like a coil absorbs or compensates for the energy generated by the cable. Ignition leads equipped with an inductive resistor are wrapped with two layers of silicone and a layer of fiberglass. The internal silicone insulation ensures durability and protects against high voltages.

The fiberglass fabric increases the mechanical strength of the cable. The exterior silicone rubber insulation withstands temperatures up to 220°C and is resistant to hydrocarbons.

Read moreShow less
€28.00 (tax incl.)
Order before 1pm and enjoy same day shipping !
In stock
Product Details
4L-711
You may also like
Spark plug wire harness - 1 Spark plug wire harness - 1

  • This ignition harness consists of4 spark plug wires and 1 coil wire.
  • We would like to point out that our spark plug wires are made with Ø 7 mm silicone wires, black in color, with a standard copper core (wire material), which indicates that they do not have interference protection.
  • If the vehicle is equipped with sensitive electronic accessories, such as Radios, tripmasters, monitors, or certain electronic ignition kits may cause interference or disruption.
Reference: 1707
€21.00 (tax incl.)
Add to cart
In stock
Customers who bought this product also bought:
Set of 4 pistons and 4 Ø70mm liners with segments and pin (Engine type 688) - 1 Set of 4 pistons and 4 Ø70mm liners with segments and pin (Engine type 688) - 1

Suitable for:

    • Estafette: Cléon 1108cc engine
    • R4 F6/GTL (Engine 688, C1E): Cléon 1108cc engine
    • R5 TL/GTL and Commercial Vehicles: Cléon 1108cc engine
    • R6 TL: Cléon 1108cc engine
    • R8 Major (R1132) / R8S (R1136): Cléon 1108cc engine
    • R10: Cléon engine 1108 cm³

The sets are supplied with the following components:

  • Liners (x4)
  • Pistons (x4)
  • Rings (x12)
  • Pin pins (x4)

Dimensions of the various parts:

  • Liner bore diameter: Ø 70 mm
  • Flange or top diameter (D): Ø 85.80 mm
  • Liner base diameter (A):Ø 75.44mm
  • Overall height including skirts of cylinder liners (C): 135mm
  • Height from top of cylinder liner to base seal area (E): 94.85mm
  • Panel dimensions: Ø 18x62mm (Cirlip-free mounting)
  • Ring thickness: 2mm / 2mm / 3.5mm (Fireproof/Sealing/Scraper)
  • Base seal type: Paper gasket

Piston mounting direction: one arrow drawn perpendicular to the axis of the piston, figure on the top of the piston. It must be oriented in the direction of engine rotation during the connecting rod's downward stroke (see manufacturer's instructions or diagram).

It is essential to check the ring end gap of each piston ring before installing them on the pistons, according to the values ​​given by the manufacturer or in the supplied instructions.

During installation, the ring end gap must be evenly distributed around the piston circumference at 120° intervals.

Reference: 4001
€330.00 (tax incl.)
Add to cart
In stock
12V electronic ignition kit with tray for Ducellier distributor WITHOUT depression - 1 12V electronic ignition kit with tray for Ducellier distributor WITHOUT depression - 1

  • Kit to be used with a coil of primary resistance between 2.5 and 3.5 ohms
  • Compatible with coils AVP4708 and AVP4715
  • Compatible for Ducellier igniter with an internal body diameter of Ø 58.8mm
  • Not suitable for an igniter with externally adjusted breakers (different plate fixing points)
  • 12V electronic ignition kit, with magnetic trigger which allows the elimination of the breakers and the capacitor
  • Notice included
  • Supplied with 3 screws for fixing the plate
  • Instructions included
Reference: 4799
€74.00 (tax incl.)
Add to cart
In stock
1

Please sign in first.

Sign in