Out of stock
Front wheel hub for disc brake
Reference:
43015
Hub Specifications:
- Outer Diameter: Ø 180mm
- Inner Bearing Race Diameter: Ø 47mm
- Wheel Stud Hole Diameters: Ø 13.5mm
- Wheel Stud Bolt Hole Spacing: 3x130mm
- Brake Disc Bolt Hole Diameters: Ø 10mm
- Brake Disc Bolt Hole Spacing: 3x71mm
- Center Cap Bolt Diameter: Ø 42mm
- Hub sold without bearing and without stud
- Renault OE ref: 0833144700 / 0833096600 / 7701455396
€60.00
(tax incl.)
Order before 1pm and enjoy same day shipping !
You may also like
Dowel Dimensions:
- Dowel Thread: M12 ((125 Pitch / Class 10.9)
- Dowel Head Diameter: Ø 19.50mm
- Dowel Recess Diameter: Ø 14.30mm
- Dowel Length Under Head: 33mm
- Dowel Overall Length: 38mm
Suitable for:
- Alpine A110 1300 / 1600: (Front and rear hubs with disc brakes)
- Alpine GT4:(Front and rear hubs with disc brakes)
- Caravelle: (R1133) / Floride (R1131):(Front and rear hubs with disc brakes)
- Dauphine: R1094 and R1095(Front and rear hubs with disc brakes)
- Matradjet:(Front and rear hubs with disc brakes)
- R8 / R10: (Front hubs with disc brakes)
- R8 G: R1135 (Front and rear hubs with disc brake)
- R12: All models (Rear hub with drum brake)
- R12 G: R1173 (Front and rear hubs with disc brake)
- R16 TS: R1151 (Rear hub with drum brake)
- R16 L/TL: R1153 (Front hub with disc brake and rear hub with drum brake)
- R17 TL: R1312 From serial number 30471 to the end of series 30470 (Front hub with disc brake and rear hub with drum brake)
- R17 TL: R1322 From serial number 2451 to the end of series 30470 Series (Front hubs with disc brake and rear hubs with drum brake)
- R17 G:(Front and rear hubs with disc brake)
Out of stock
Out of stock
In stock
In stock
Customers who bought this product also bought:
In stock
For engine with 4-outlet water pump.
Kit sold without valve stem seals (AVP1012), without copper base seals and without the timing case oil seal (AVP1029).
Out of stock
-
- Overall length: 256.5 cm
- Sheath length: 194.5 cm
- Cable length: 245.5 cm
Our cables are made in France and meet the assembly and quality standards of original equipment (OEM) cables from automotive manufacturers.
In stock
In stock
For engine with water pump, x4 outlets.
Kit sold without valve stem seals (AVP1012), without copper base seals and without the timing case oil seal (AVP1029).
Out of stock
With location for chrome strip
In stock
Kit specifications (Tie rods / Ball joints and boots):
- Ball joint taper diameter (Steering knuckle side): Top of taper Ø 11mm / Bottom of taper Ø 12mm
- Ball joint taper stud thread diameter: M10 x 1.25 (right-hand thread)
- Ball joint stud thread diameter (into tie rod): M14 x 1.50 (right-hand thread)
- Tie rod thread diameter (into steering rack): M12 x 1.00 (right-hand thread)
- Minimum length of tie rod/ball joint assembly: 26 cm (measured from the contact point against the steering rack to the center of the ball joint stud on the steering knuckle side)
- Maximum adjustment of the tie rod/ball joint assembly: 29 cm (measured from the contact point against the steering rack to the center of the ball joint at the steering knuckle end)
- Includes: 2 steering rack boots, 2 steering ball joints (with nuts and locknuts), and 2 steering tie rods.
Suitable for:
- R8 (All models)
- Caravelle / Floride S
- A110 (All models) / Alpine GT4
- Matradjet
This adjustable steering kit replaces the original "fork-type" steering tie rods.
To install the adjustable tie rods, you must remove the steering rack eyelet bushing and replace the steering rack boots with the specific AVP4620 boots (included in the kit).
Out of stock