To turn on a temperature warning light
Trigger temperature 105°C
In stock
Pair of solid brake discs - Ø 254mm x thickness 12mm (Large brake type mounting) - 3 fixing holes (Center distance R16)
Reference:
4444
Suitable for:
- R8 / R8G / A110 : Front or rear disc (Big brake assembly)
- A110 1600 SX (VH) : Front or rear disc
- R16 (L / TL / TS) / R16TX : Front disc
- A310.4 (No. 910 at the end of the series): Front disc
- A310 V6 - Before 1980 (No. 1 to No. 47708 ): Rear disc
Réf OE Renault : 0428906000 / 7700572631
€138.00
(tax incl.)
Order before 1pm and enjoy same day shipping !
The brake discs are designed for a Renault 16 hub with a centering of Ø 84mm.
They are compatible with the R8 and A110 assembly with a hub centering of Ø 60mm, provided that the centering shims provided for the assembly of the "Big brakes" are used.
It is necessary to re-drill the wheel hubs according to the fixing center distance of the brake discs provided.
Please note, it is mandatory to make the countersinks on the hubs, countersinks which allow the fixing nuts of the brake disc to be drowned in order to avoid any contact between the inside of the rim and the nuts of fixing the brake disc. If this operation is not followed, the wheel may not be properly tightened.
Customers who bought this product also bought:
 - 3 fixing holes (Center distance R16)&media=https://www.arnaudventouxpieces.com/764-large_default/pair-of-solid-brake-discs-o-254mm-x-thickness-12mm-big-brake-3-mounting-holes.jpg){kind=link}
In stock
Delivery in France only
- Does not absorb moisture, thus protecting brake systems from rust, which accumulates on wheel cylinders and destroys the brake pads after a few brake applications when the brakes are restarted in the spring.
- DOT 5 approved (not to be confused with DOT 5.1)
Directions for use:
- Before using this brake fluid, your system must be thoroughly bled, rinsed with rubbing alcohol, and dried.
.jpg)
In stock
The kit contains:
- 4 x 8mm smooth-bore screws - M8 thread (to be positioned on the wheel side)
- 4 x 8.4mm smooth-bore screws - M8 thread (to be positioned on the body or chassis side)
Alpine / Renault OE Ref: 0706289800 / 0706290200
A kit is required to equip both front wishbones of a car
In stock
ATTENTION: Suitable for "large" brake mounting with a 12mm thick disc and a non-offset brake caliper bracket identical to REF AVP 4377.
Kit for mounting large wheel bearings on the rear axle, including:
- 2 Bearing carriers machined from hardened and burnished 42CrMo4 steel,
- 2 Double-row bearings with a high-temperature resistant polyamide cage (which prevents seizing in case of cage damage), with a double water-resistant seal (the axle grease fitting can be removed as the bearing is sealed),
- 2 10-spline hubs with 10.9 wheel studs,
- 6 Studs with reinforced locking nuts (gluing the studs is recommended for mounting in the axles) bearings).
- 2 Rear hub castellated nuts M20 x 150
- 2 Rear hub conical washers Ø 20mm
- 2 Pins
Eliminates wheel play and improves axle guidance,
Improves differential oil seal sealing,
Improves geometry and handling precision,
Kit ready to be mounted on the original axle housing without modification,
CAUTION: It is recommended to check the axle alignment and the centering of the brake disc relative to the brake caliper bracket/clamp.
Out of stock
- Overall length: 254 cm
- Sheath length: 247.5 cm
- Cable length: 254 cm
Our cables are made in France and meet the assembly and quality standards of original equipment (OEM) cables from automotive manufacturers.
In stock
In stock