ATTENTION: Suitable for mounting "small" original brakes with original caliper and brake disc

Kit for mounting large wheel bearings on the rear axle, including:

• 2 Bearing carriers machined from 42CrMo4 hardened and burnished steel,
• 2 Double-row bearings with high-temperature resistant polyamide cages (which prevents seizing in case of cage damage), with a double water-resistant seal (the axle grease fitting can be removed as the bearing is sealed),
• 2 10-spline hubs with 10.9 wheel studs,
• 6 Studs with reinforced brake nuts (gluing the studs is recommended for installation in the bearing housings).

  Eliminates wheel play and improves axle guidance.

  Improves differential oil seal sealing.

  Improves geometry and handling precision.

  Ready to be mounted on the original axle housing without modification.

  CAUTION: It is recommended to check the axle alignment and the centering of the brake disc relative to the brake caliper bracket/clamp.

ATTENTION: Suitable for "large" brake mounting with a 12mm thick disc and a non-offset brake caliper bracket identical to REF AVP 4377.

Kit for mounting large wheel bearings on the rear axle, including:

• 2 Bearing carriers machined from hardened and burnished 42CrMo4 steel,
• 2 Double-row bearings with a high-temperature resistant polyamide cage (which prevents seizing in case of cage damage), with a double water-resistant seal (the axle grease fitting can be removed as the bearing is sealed),
• 2 10-spline hubs with 10.9 wheel studs,
• 6 Studs with reinforced locking nuts (gluing the studs is recommended for mounting in the axles) bearings).

 Enables the elimination of wheel play and improved wheel shaft guidance,

 Improves the sealing of the differential oil seals,

 Improved geometry and handling precision,

 Kit ready to be mounted on the original axle housing without modification,

 CAUTION: It is recommended to check the wheel shaft alignment and the centering of the brake disc relative to the brake caliper bracket/clamp.

• • ATTENTION: straight, non-offset bracket for mounting a Bendix-type "big brake" caliper bracket
  • Brake bracket mounting hole spacing: 100mm
  • Original Alpine part number: 6000001437
  • Fixing with AVP4300 screws
  • ATTENTION, suitable for:

-Big brake setup identical to the original: 10mm thick rear brake disc (12mm - 2mm on the inner face) + Bendix R16 bracket with 100mm mounting hole spacing + original single-row wheel bearing + original hub

or

-Big brake setup with: Big bearing kit REF AVP6413 + 12mm rear brake disc REF AVP4444 + Bendix R16 bracket with 100mm mounting hole spacing

It is essential, in all cases, to check the centering of the brake disc in the Bendix bracket.

• Screw for tightening the "Bendix" yoke to its support
• Dimensions: 12x125
• Reinforced series
• Suitable for AVP support REF4377

• Suitable for 1100/1300 GORDINI
• Supplied with M7 stud, washer, and nut

• Velcro fastening
• Black imitation leather interior door panels mounted on reinforced panels for Alpine A110 with round handle (up to 1973)
• Set of 4 trim pieces for both doors
• Premium finish

• Velcro fastening
• Black leatherette interior door panels mounted on reinforced panels for Alpine A110 with round handle (up to 1973)
• Set of 4 trim pieces for both doors
• Premium finish

• • For use during track days, track days, or for classic cars
  • Shoulder strap width: 49mm
  • Waist strap width: 49mm
  • Adjustable shoulder and lap belt
  • Flat 3-point mounting with included 7/16 UNF screws
  • EEC approved

Caution: For road use and to comply with the Highway Code, you must retain your vehicle's original seat belts. Not FIA approved

• • For use during track days, track days, or for classic cars
  • Shoulder strap width: 49mm
  • Waist strap width: 49mm
  • Adjustable shoulder and lap belt
  • Flat 3-point mounting with included 7/16 UNF screws
  • EEC approved

Caution: For road use and to comply with the Highway Code, you must retain your vehicle's original seat belts. Not FIA approved

• • For use during track days, track days, or for classic cars
  • Shoulder strap width: 49mm
  • Waist strap width: 49mm
  • Adjustable shoulder and lap belt
  • Flat 3-point mounting with included 7/16 UNF screws
  • EEC approved

Caution: For road use and to comply with the Highway Code, you must retain your vehicle's original seat belts. Not FIA approved