Outer diameter: 260mm
Hub passage diameter: 60mm
Center distance of the 3 fixing holes: 71mm
Thickness: 8mm
In stock
Braking R8 / R8S / R8G
Our braking spare parts for the Renault R8 / R8S / R8G
Discover here a wide choice of parts to restore and ensure the proper functioning of the braking system of your Renault R8 / R8S / R8 Gordini.
Whether you are looking for wheel cylinders, hoses, master cylinders, brake discs, original brake calipers, big brake calipers, lockheed, reservoir, connector, stop switch, repair kit, copper braking circuit...at AVP, Arnaud Ventoux Pièces, you will find everything you need to bring your old one back to life with quality components.
In stock
In stock
In stock
Suitable for front or rear (need 2 sets for one car)
Competition type pads, efficient in cold and high temperatures,
Friction coefficient of 0.43 µ,
Use reserved for competition, do not use these pads on public...
In stock
End cap for stop switch Ø 12.5mm
Mounting using a long rod
In stock
In stock
Length taken from the axis of the fixing eye to the end of the rod: min adjustment 77mm / max 87mm
In stock
In stock
Length taken from the axis of the fixing eye to the end of the rod: min adjustment 105mm / max 115mm
In stock
Master Cylinder Side (Male Thread): M16x150
Copper Pipe Fitting Side (Female Thread): Ø 1/2"-20 UNF (Ø 12.70mm)
In stock
In stock
Thread (master cylinder side): M16x150
Nozzle (rubber hose connection side): Ø 10mm
In stock
In stock
Mounts with the stop switch reference 4423
In stock
In stock
Sold complete with teat (inside Ø 6mm), insert, support and cap.
In stock
In stock
In stock
In stock
In stock
Sold in 1ml lengths
In stock
In stock
Length 1 meter
In stock
In stock
In stock
In stock
The entire kit is made up of 3/8"-24UNF fittings
This kit is composed of the following copper pipes:
- From the brake master cylinder to the Right Front Wheel
- From the brake master cylinder to the Left Front Wheel
-...
In stock
In stock
In stock
Fully open position, release pressure 8 bars (+/- 5bars)
In stock
In stock
In stock
In stock
Suitable for:
4CV: Drum brake (From 06/1953 until end of series)
Alpine A106: Drum brake
Dauphine (All models): Disc brake
Caravelle / Floride: Disc brake
R10 / R8 (All models): Disc brake
Alpine A110 and GT4: Disc...
In stock
Suitable for:
4CV: Drum brake (From 06/1953 until end of series)
Alpine A106: Drum brake
Dauphine (All models): Disc brake
Caravelle / Floride: Disc brake
R10 / R8 (All models): Disc brake
Alpine A110 and GT4: Disc...
In stock
4CV: Drum brake (From 06/1953 until end of series)
Alpine A106: Drum brake
Dauphine (All models): Disc brake
Caravelle / Florida: Disc brake
R10 / R8 (All models): Disc brake
Alpine A110 and GT4: Disc brake
Matradjet:...
In stock
In stock
In stock
Caliper equipped with square joint.
Fit on:
Dauphine (Disc brakes)
R8 / Caravelle / Floride S
A110 (Small brakes mounting)
In stock
Caliper equipped with square joint.
Fit on:
Dauphine (Disc brakes)
R8 / Caravelle / Floride S
A110 (Small brakes mounting)
In stock
Sold without adjusting screws or handbrake lever. Caliper equipped with a square seal.
Suitable for:
Dauphine / Dauphine Export (Disc brakes)
R8 / Caravelle / Floride S
A110 (Small brake setup)
Matra Djet: Left Rear...
In stock
Sold without adjusting screws or handbrake lever. Caliper equipped with a square seal.
Suitable for:
Dauphine / Dauphine Export (Disc brakes)
R8 / Caravelle / Floride S
A110 (Small brake setup)
Matra Djet: Right Rear...
In stock
This kit contains an M9 adjustment screw nut and an M8 nut.
Kit sold with a strong Ø 38mm square gasket and a weak Ø 38mm gasket.
The supply of these two seals allows you to install the most suitable seal depending...
In stock
This kit contains an M9 adjustment screw nut and an M8 nut
To identify a caliper with a square or round joint, refer to the symbol indicated on the caliper casting.
A square symbol indicates a square joint, while a...
In stock
This kit contains an M9 adjustment screw nut and an M8 nut.
To identify a caliper with a square or round seal, refer to the symbol indicated on the caliper casting.
The "square" symbol indicates the presence of a...
In stock
This kit contains an M9 adjustment screw nut and an M8 nut
To identify a caliper with a square or round seal, refer to the symbol indicated on the caliper casting.
A square symbol indicates a square seal, while a...
In stock
In stock
In stock
For a cable with a cable stop end: Ø 14mm
OE Renault Ref: 8704054 / 0870405400
In stock
In stock
In stock
In stock